We take cryptocurrency — so the coins you hold can buy real hardware.Pay in crypto, spend it on real hardware. Free insured shipping worldwide over $399. Plain, unbranded boxes, sent from Germany.Free insured shipping over $399. Your rate is locked for 30 minutes once checkout opens.Rate locked 30 minutes. Every item sealed, serial-checked and covered by a 24-month warranty.Sealed, 24-month warranty.

Saved items Sign in
Gray shielded Cat6 Ethernet cable 35 ft with snagless RJ45 connectors

Cables To Go

Cables To Go 00790 Cat6 shielded network ethernet cable 35 ft gray

SKU CH-HA83-SZ7JG MPN 00790

Shielded Cat6 patch cable, 35 ft, reduces EMI/RFI interference for reliable network connections

  • TypeConsumer Electronics
  • Cat6
  • Connector ARJ45
  • Connector BRJ45
  • Length35 ft.
  • ColorGray
  • Cat6 rating supports gigabit network speeds
  • Shielded construction blocks EMI and RFI interference
  • Snagless boots protect connector tabs during installation
  • 35 ft length reaches distant network devices
  • Tested to ANSI/TIA 568 C.2 Cat6 component requirements

Cat6 shielded cable for noisy environments

This 35 ft gray patch cable uses shielded Cat6 construction to protect high-speed networks from EMI and RFI interference. It connects network adapters, hubs, switches, routers, modems and patch panels in high-noise environments where unshielded cables may suffer signal degradation.

Thermals noise and power draw

As a passive copper cable, it produces no heat, generates no noise and draws no power during operation. Signal integrity is maintained through bonded pair construction that preserves twist spacing to the termination point, minimizing Near-End Crosstalk without active components.

ANSI/TIA 568 C.2 Cat6 component compliance

Each cable is fully tested to meet ANSI/TIA 568 C.2 Cat6 component requirements, ensuring it handles bandwidth-intensive voice, data and video distribution. This certification is the single specification that confirms the cable will perform to Cat6 standards in structured wiring installations.

Highlights

  • Cat6 rating supports gigabit network speeds
  • Shielded construction blocks EMI and RFI interference
  • Snagless boots protect connector tabs during installation
  • 35 ft length reaches distant network devices
  • Tested to ANSI/TIA 568 C.2 Cat6 component requirements

Specifications

BrandC2G
Model00790
TypeConsumer Electronics
Cat6
Connector ARJ45
Connector BRJ45
Length35 ft.
ColorGray
ShieldedYes
FeaturesProtect from EMI/RFI interference; connect network adapters, hubs, switches, routers, DSL/cable modems, patch panels and other networking applications in high noise environments.
Shipping weight0.60 kg
Package size305 × 254 × 203 mm

Questions about this item

How do I install the 35 ft shielded Cat6 cable without damaging the RJ45 connectors?

Push each RJ45 plug straight into the port until the snagless tab clicks; the bonded pair construction keeps twists intact to the termination point, so avoid sharp bends or kinking the 10.66 metre run during routing.

What maintenance will the shielded Cat6 cable need over time?

Inspect the gray jacket and RJ45 tabs periodically for cracks or corrosion; the shielded design resists EMI/RFI, but physical damage to the shield or connectors can degrade performance in high-noise environments.

At what point does signal loss become noticeable on a 35 ft Cat6 run under sustained load?

The cable meets ANSI/TIA 568 C.2 component requirements, so attenuation stays within Cat6 limits for the full 35 foot length; excess loss appears only if connectors are poorly seated or the cable is sharply bent beyond its minimum bend radius.

New to this? Which coin should you pay with — what to check, what it costs to pay, and what is never asked for.

Also in this aisle

People compared these

Same shelf, same checkout — eight coins and a 30-minute rate lock.