We take cryptocurrency — so the coins you hold can buy real hardware.Pay in crypto, spend it on real hardware. Free insured shipping worldwide over $399. Plain, unbranded boxes, sent from Germany.Free insured shipping over $399. Your rate is locked for 30 minutes once checkout opens.Rate locked 30 minutes. Every item sealed, serial-checked and covered by a 24-month warranty.Sealed, 24-month warranty.

Saved items Sign in
Black 10 ft Cat6a snagless UTP patch cable with molded RJ-45 connectors on both ends

Cables To Go

Cables To Go 00732 10ft Cat6a snagless UTP network ethernet cable black

SKU CH-2DP3-FYBJH MPN 00732

A 10 ft Cat6a UTP patch cable with snagless RJ-45 connectors, tested to ANSI/TIA 568 C.2 for 10 Gigabit Ethernet up to 100 metres

  • TypeConsumer Electronics
  • ColorBlack
  • Supports 10 Gigabit data rates over copper
  • Snagless boot protects the RJ-45 latch during use
  • Fully tested to ANSI/TIA 568 C.2 Cat6a channel specs
  • 10 ft length suits typical desk-to-switch runs
  • Unshielded twisted-pair construction keeps the cable flexible

Ready for 10 Gigabit networks

This 10 ft Cat6a patch cable supports 10 Gigabit data transmission over four-pair copper up to 100 meters. It meets ANSI/TIA 568 C.2 Cat6a channel requirements and is fully tested for that performance level. The cable uses unshielded twisted-pair construction with RJ-45 male connectors on both ends. It suits home, office or data-centre links that need the higher bandwidth of Cat6a.

Snagless boots simplify installation

Moulded snagless boots protect the connector tabs from catching on adjacent cables or patch-panel ports during routing. The flexible UTP jacket bends easily around cable-management trays and through tight cabinet openings. Because the connectors are pre-terminated and tested, no field termination or specialised tools are required. The only common issue is exceeding the 100 metre channel limit, which will degrade 10 Gigabit signal integrity.

Verify your infrastructure first

Ensure the switch, router and network interface cards at both ends are rated for 10 Gigabit Ethernet. Confirm that any existing horizontal cabling, patch panels and wall outlets are also Cat6a or better so the full channel meets the standard. Check that the 10 ft length fits your rack or desk layout without leaving excessive slack. The cable is unshielded, so keep it clear of strong EMI sources such as power distribution units.

Highlights

  • Supports 10 Gigabit data rates over copper
  • Snagless boot protects the RJ-45 latch during use
  • Fully tested to ANSI/TIA 568 C.2 Cat6a channel specs
  • 10 ft length suits typical desk-to-switch runs
  • Unshielded twisted-pair construction keeps the cable flexible

Specifications

BrandCables To Go
Model00732
TypeConsumer Electronics
ColorBlack
Shipping weight0.13 kg
Package size140 × 127 × 32 mm

Questions about this item

How can I verify the cable delivers 10 Gigabit speeds after installation?

Connect it between 10 Gigabit ports and run a throughput test; the cable is tested to meet ANSI/TIA 568 C.2 Cat6a channel requirements for 10 Gbps up to 100 meters.

What comes in the package and what must I provide separately?

The box contains one 10 ft Cat6a snagless UTP patch cable with RJ-45 male connectors on both ends; you supply the network devices and any wall plates or keystones.

Which length should I choose for a desktop-to-switch run under 10 feet?

The 10 ft version leaves enough slack for routing without excess coil; if the distance is significantly shorter, a shorter Cat6a patch cable would reduce clutter.

New to this? Which coin should you pay with — what to check, what it costs to pay, and what is never asked for.

Also in this aisle

People compared these

Same shelf, same checkout — eight coins and a 30-minute rate lock.