We take cryptocurrency — so the coins you hold can buy real hardware.Pay in crypto, spend it on real hardware. Free insured shipping worldwide over $399. Plain, unbranded boxes, sent from Germany.Free insured shipping over $399. Your rate is locked for 30 minutes once checkout opens.Rate locked 30 minutes. Every item sealed, serial-checked and covered by a 24-month warranty.Sealed, 24-month warranty.

Saved items Sign in
Blue Cat6a Ethernet cable with snagless RJ45 connectors, 9 ft length

Cables To Go

Cables To Go 00697 Cat6a network ethernet cable 9 ft blue

SKU CH-1F0X-ZXZ14 MPN 00697

A 9 ft Cat6a patch cable with snagless RJ-45 connectors for 10 Gigabit Ethernet links

  • TypeCategory 6a
  • CatCategory 6a
  • Connector A1 x RJ-45 Male Network
  • Connector B1 x RJ-45 Male Network
  • Length9 ft.
  • ColorBlue
  • 10 Gigabit network speed supported by Cat6a rating
  • Snagless connectors prevent latch damage during routing
  • Blue jacket enables quick colour-coding of runs
  • 9 ft length fits standard desk-to-switch distances
  • ANSI/TIA 568 C.2 tested for reliable 10GBase-T performance

Cat6a patch cable for 10GBase-T

This 9 ft Cat6a patch cable uses RJ-45 male connectors on both ends. It is built to meet ANSI/TIA 568 C.2 component requirements for Category 6a performance. The blue jacket allows quick colour-coding in a rack or at a desk. Each cable carries an individual length label for easy identification.

Bonded-pair construction under load

Bonded twisted pairs preserve consistent spacing all the way to the termination point. This design minimises Near-End Crosstalk and keeps impedance and structural return loss low during sustained 10 Gigabit throughput. The snagless boots protect the latch tabs when cables are routed through dense patch panels or tight cable managers.

Replaces lower-category patch leads

Swapping Cat5e or Cat6 patch cords for this Cat6a cable removes the bottleneck on 10GBase-T links. The upgrade is worthwhile when the switch, router or network adapter already supports 10 Gigabit speeds but the existing patch cable does not. It is not for installations that require shielded cable or lengths beyond the single 9 ft segment.

Highlights

  • 10 Gigabit network speed supported by Cat6a rating
  • Snagless connectors prevent latch damage during routing
  • Blue jacket enables quick colour-coding of runs
  • 9 ft length fits standard desk-to-switch distances
  • ANSI/TIA 568 C.2 tested for reliable 10GBase-T performance

Specifications

BrandC2G - KVM & NETWORKING
ModelA7293808
TypeCategory 6a
CatCategory 6a
Connector A1 x RJ-45 Male Network
Connector B1 x RJ-45 Male Network
Length9 ft.
ColorBlue
Shipping weight0.11 kg
Package size251 × 132 × 25 mm

Questions about this item

Does the 9 ft Cat6a cable generate any heat or draw power when it runs all day?

No, the cable is a passive copper assembly with no active electronics, so it produces no measurable heat and consumes zero power during continuous use.

What equipment must I already have to use the RJ-45 connectors on this patch cable?

You need devices with standard RJ-45 Ethernet ports — such as a router, switch, network card or patch panel — that accept an 8P8C plug.

Will the Cat6a cable work reliably alongside older Cat5e or Cat6 runs in the same installation?

Yes, the cable meets ANSI/TIA 568 C.2 Cat6a component requirements and is fully backward compatible, so it interoperates with existing Cat5e and Cat6 links without performance loss.

New to this? Which coin should you pay with — what to check, what it costs to pay, and what is never asked for.

Also in this aisle

People compared these

Same shelf, same checkout — eight coins and a 30-minute rate lock.