We take cryptocurrency — so the coins you hold can buy real hardware.Pay in crypto, spend it on real hardware. Free insured shipping worldwide over $399. Plain, unbranded boxes, sent from Germany.Free insured shipping over $399. Your rate is locked for 30 minutes once checkout opens.Rate locked 30 minutes. Every item sealed, serial-checked and covered by a 24-month warranty.Sealed, 24-month warranty.

Saved items Sign in
Gray snagless Cat6 patch cable, 7 ft, RJ45 ends, molded boots

CableMAX

CableMAX Cat6 7ft Gray Snagless RJ45 Patch Cable 24AWG 550MHz UTP

SKU CH-GD3S-HF0PV

A 7 ft gray Cat6 patch cable with snagless boots, 24 AWG stranded conductors and 50 µm gold-plated RJ45 connectors rated for 550 MHz

  • Connector ARJ45
  • Connector BRJ45
  • ColorGray
  • Supports Gigabit Ethernet with 550 MHz rated Cat6 cable
  • Snagless bubble boots protect RJ45 tabs during installation
  • 50 micron gold plated staggered pins reduce cross-talk
  • 24 AWG stranded conductors with four twisted pairs for flexibility
  • Backwards compatible with Cat5e and Cat5 networks

CableMAX Cat6 7 ft patch cable

This seven-foot Cat6 patch cable connects two RJ45 ports with a stranded UTP construction rated at 550 MHz. Four twisted pairs and 24 AWG conductors deliver performance that meets or exceeds the Category 6 EIA/TIA specification. Molded bubble boots and staggered gold-plated pins reduce cross-talk and prevent snags during installation. The CM fire rating and ETL verification confirm compliance for typical indoor runs.

Upgrading from Cat5 or Cat5e links

Replacing older Category 5 or 5e patch cords with this Cat6 cable raises the bandwidth ceiling to 550 MHz and supports Gigabit Ethernet speeds where the previous links topped out at 100 MHz. The staggered pin layout further suppresses near-end cross-talk, making the jump worthwhile when the network backbone and switch ports are already rated for Cat6 or higher. If the surrounding infrastructure remains Cat5e, the extra headroom will not be realised.

Check port spacing and cable routing

Verify that the RJ45 jacks on your router, switch or wall plate accept standard staggered-pin plugs without mechanical interference. Ensure the seven-foot length reaches between devices without tension or sharp bends that could degrade the 24 AWG stranded conductors. Confirm the installation environment suits a CM-rated jacket rather than a plenum or riser rating. Buyers needing longer runs, shielded construction or outdoor-rated jackets should look elsewhere.

Highlights

  • Supports Gigabit Ethernet with 550 MHz rated Cat6 cable
  • Snagless bubble boots protect RJ45 tabs during installation
  • 50 micron gold plated staggered pins reduce cross-talk
  • 24 AWG stranded conductors with four twisted pairs for flexibility
  • Backwards compatible with Cat5e and Cat5 networks

Specifications

Connector ARJ45
Connector BRJ45
ColorGray

Questions about this item

What is the cable length and connector type for fitting into a standard port?

The cable is 7ft long with RJ45 male connectors on both ends, designed to fit standard Ethernet ports on routers, switches, and network cards.

How do I insert the connector without damaging the latch, and what is the common mistake?

Press the RJ45 connector straight into the port until the snagless bubble boot latch clicks; the common mistake is forcing it at an angle which can bend the staggered gold-plated pins.

Will the gold plating or boot degrade and require cable replacement over time?

The 50 micron gold-plated contacts and molded bubble boots are built for durability; replacement is only needed if the cable is physically damaged or the latch tab breaks off.

New to this? Which coin should you pay with — what to check, what it costs to pay, and what is never asked for.

Also in this aisle

People compared these

Same shelf, same checkout — eight coins and a 30-minute rate lock.