We take cryptocurrency — so the coins you hold can buy real hardware.Pay in crypto, spend it on real hardware. Free insured shipping worldwide over $399. Plain, unbranded boxes, sent from Germany.Free insured shipping over $399. Your rate is locked for 30 minutes once checkout opens.Rate locked 30 minutes. Every item sealed, serial-checked and covered by a 24-month warranty.Sealed, 24-month warranty.

Saved items Sign in
Black internal cable with one Mini SAS HD SFF-8643 connector splitting to four SATA 7-pin plugs

Cablecc

Cablecc Mini SAS HD SFF-8643 to 4 SATA 7pin 1.50 ft network ethernet cable

SKU CH-9Q9B-EH4YH

Connects four SATA drives to a Mini SAS HD SFF-8643 controller at 6 Gb/s over 1.50 ft

  • Cat6
  • Length1.50 ft.
  • ColorBlack
  • Connect up to four SATA drives to a Mini SAS HD SFF-8643 controller
  • Supports 6 Gb/s data transfer under the SAS 2.1 standard
  • HD Mini-SAS connectors designed for future 12 Gb/s SAS 3.0 speeds
  • 50 ft length fits compact server and RAID chassis
  • Black cable with SFF-8643 host and four SATA 7-pin device connectors

Host-to-four-drive connectivity

This internal cable links a Mini SAS HD SFF-8643 host port to four SATA 7-pin drives. It suits server and RAID builders who need to break out a single controller lane to multiple hard disks. The 1.50 ft length fits compact chassis routing. Buyers needing longer runs or external connectors should look elsewhere.

Signal integrity at 6 Gb/s

The copper assembly meets the SAS 2.1 standard for 6 Gb/s operation and uses the HD connector family that will carry forward to the SAS 3.0 specification at 12 Gb/s. No active components or power draw are introduced by the cable itself. Thermal and acoustic impact inside the case is negligible.

Four SATA breakout ends

Each of the four SATA 7-pin tails terminates a single drive connection, letting one host port serve up to four disks without extra controllers. The bundle contains only the cable; no brackets, screws or software are included. Installers must supply their own drive mounting and controller configuration.

Highlights

  • Connect up to four SATA drives to a Mini SAS HD SFF-8643 controller
  • Supports 6 Gb/s data transfer under the SAS 2.1 standard
  • HD Mini-SAS connectors designed for future 12 Gb/s SAS 3.0 speeds
  • 50 ft length fits compact server and RAID chassis
  • Black cable with SFF-8643 host and four SATA 7-pin device connectors

Specifications

Cat6
Length1.50 ft.
ColorBlack

Questions about this item

How do I plug the Mini SAS HD SFF-8643 end into my controller without bending the latch?

Align the keyed HD Mini-SAS connector with the controller port, push straight in until the latch clicks, then route the four SATA 7-pin tails to each drive; the latch releases by squeezing the sides, not by pulling the cable.

Will the SATA 7-pin connectors or the cable itself need replacement after heavy RAID rebuilds?

The copper conductors are rated for the 6 Gb/s SAS 2.1 spec; connectors are rated for typical server insertion cycles, so only replace if a latch breaks or a drive reports persistent CRC errors.

At what throughput does the 1.50 ft cable hit its signal-integrity limit during sustained 6 Gb/s transfers?

The assembly meets the SAS 2.1 6 Gb/s specification across its full 0.5 m length; sustained RAID traffic at that rate stays within the validated eye-diagram margin.

New to this? Which coin should you pay with — what to check, what it costs to pay, and what is never asked for.

Also in this aisle

People compared these

Same shelf, same checkout — eight coins and a 30-minute rate lock.