We take cryptocurrency — so the coins you hold can buy real hardware.Pay in crypto, spend it on real hardware. Free insured shipping worldwide over $399. Plain, unbranded boxes, sent from Germany.Free insured shipping over $399. Your rate is locked for 30 minutes once checkout opens.Rate locked 30 minutes. Every item sealed, serial-checked and covered by a 24-month warranty.Sealed, 24-month warranty.

Saved items Sign in
Three black braided PWM fan splitter cables, 10 inches each, 4-pin to three connectors

Cable Matters DGZY0037 PWM Fan Splitter Cable 10 in 3 Pack Black

SKU CH-V13T-BT7BE

Connects three PWM fans to one motherboard header for synchronised speed control

  • ColorBlack
  • Length< 1"
  • Connector Number3
  • Connector DetailDVI to DVI
  • Terminal GenderFemale to Female
  • SpecificationsCopper, PVC/TPE, Display Port, 0.51, millimeters, DGZY0037,
  • Connect three PWM fans to one motherboard header for synchronised speed control
  • Braided 24 AWG nylon sleeving protects wires and resists wear
  • Works with both 4-pin and 3-pin case fans for broad compatibility
  • 10-inch length reaches fans across mid-tower cases without strain
  • Three cables per pack supply multiple headers or spare builds

PWM Fan Splitter Cable 10 Inches

This Cable Matters splitter divides one motherboard 4-pin PWM header into three fan connections. Each 10-inch cable carries a 4-pin lead and two 3-pin leads so all attached fans receive the same PWM speed signal. The 24AWG conductors are wrapped in braided nylon sleeving for durability inside the case. A pack contains three identical splitters for multiple headers.

Builders Using One Header For Three Fans

Suits anyone adding extra case or radiator fans without free motherboard headers. The single 4-pin connector limits total current to what that header can supply, so high-amperage fans may need a powered hub instead. Systems requiring independent speed curves per fan cannot use this passive splitter.

10 Inch Cable Length

At 10 inches the leads reach nearby fan mounts but may fall short in full-tower chassis or rear-routing layouts. Measure header-to-fan distance before ordering; longer runs will require a different cable.

Highlights

  • Connect three PWM fans to one motherboard header for synchronised speed control
  • Braided 24 AWG nylon sleeving protects wires and resists wear
  • Works with both 4-pin and 3-pin case fans for broad compatibility
  • 10-inch length reaches fans across mid-tower cases without strain
  • Three cables per pack supply multiple headers or spare builds

Specifications

BrandCable Matters
ModelDGZY0037
ColorBlack
Length< 1"
Connector Number3
Connector DetailDVI to DVI
Terminal GenderFemale to Female
SpecificationsCopper, PVC/TPE, Display Port, 0.51, millimeters, DGZY0037, Menewstart
ConductorCopper Conductor
FeaturesCopper, PVC/TPE, Display Port, Menewstart, 0.51

Questions about this item

Do I need a 4-pin PWM motherboard header to use the 3-way splitter?

Yes, the cable connects to a single 4-pin motherboard header and splits the PWM signal to three fans, with one 4-pin and two 3-pin connectors.

Will my existing 3-pin case fans work with the two 3-pin branches on this cable?

The two 3-pin connectors support 3-pin fans, allowing them to run from the same header while the 4-pin branch carries the PWM speed signal.

How can I confirm the splitter is regulating fan speeds correctly after installation?

Check the motherboard fan-control software or BIOS; all three connected fans should report the same RPM and respond together to PWM duty-cycle changes.

New to this? Which coin should you pay with — what to check, what it costs to pay, and what is never asked for.

Also in this aisle

People compared these

Same shelf, same checkout — eight coins and a 30-minute rate lock.