We take cryptocurrency — so the coins you hold can buy real hardware.Pay in crypto, spend it on real hardware. Free insured shipping worldwide over $399. Plain, unbranded boxes, sent from Germany.Free insured shipping over $399. Your rate is locked for 30 minutes once checkout opens.Rate locked 30 minutes. Every item sealed, serial-checked and covered by a 24-month warranty.Sealed, 24-month warranty.

Saved items Sign in

Cable Leader

Cable Leader Cat5e Non-Booted Ethernet Cable 3ft Green 24AWG 350MHz

SKU CH-5XAY-EF5TZ

A 3 ft green Cat5e patch cable with a non-booted RJ45 design for high-density panels, 24 AWG bare copper, 350 MHz tested, Gigabit Ethernet support

  • TypeNetwork Ethernet Cables
  • Cat5E
  • Connector ARJ45
  • Connector BRJ45
  • Length3 ft.
  • ColorGreen
  • Supports 1 Gbps Gigabit Ethernet tested to 350 MHz bandwidth
  • Non-booted plug fits high-density patch panels and keystone jacks
  • 24 AWG bare copper conductors with 50-micron gold-plated contacts
  • Unshielded twisted pair design for structured cabling and PoE devices
  • RoHS compliant with UL and ETL verification for safety standards

Cable Leader Cat5e Non-Booted Ethernet Cable 3ft

The Cable Leader Cat5e non-booted Ethernet cable is a 3-foot green patch cord built to the Category 5e standard and tested to 350 MHz. It uses 24 AWG bare copper conductors in four twisted pairs and terminates in 8P8C RJ45 plugs with 50-micron gold-plated contacts. The cable supports Gigabit Ethernet (1000BASE-T) for reliable wired connectivity. It is RoHS compliant and UL & ETL verified.

Non-booted RJ45 design for high-density patch panels

The non-booted plug removes the molded boot found on standard patch cables, allowing the connector to seat easily in tightly packed patch panels and keystone jacks. This design improves airflow around dense equipment and simplifies cable management in structured cabling installations. It replaces booted Cat5e or lower-category cables where physical space is constrained. The upgrade is worth it when rack density or airflow management are priorities over connector strain relief.

Verify connector clearance and category requirements

Before ordering, confirm that your patch panels, keystone jacks, switches and PoE devices accept non-booted RJ45 plugs without latch interference. Ensure the Category 5e 350 MHz rating meets the bandwidth needs of your Gigabit Ethernet links. Check that a 3-foot length suits the distance between your devices and that the green colour matches your cable-management scheme. The cable is part of the C5102 family if colour-coded runs are required.

Highlights

  • Supports 1 Gbps Gigabit Ethernet tested to 350 MHz bandwidth
  • Non-booted plug fits high-density patch panels and keystone jacks
  • 24 AWG bare copper conductors with 50-micron gold-plated contacts
  • Unshielded twisted pair design for structured cabling and PoE devices
  • RoHS compliant with UL and ETL verification for safety standards

Specifications

TypeNetwork Ethernet Cables
Cat5E
Connector ARJ45
Connector BRJ45
Length3 ft.
ColorGreen
ShieldedNo
Wire Gauge24 AWG

Questions about this item

Will the non-booted RJ45 plugs fit a high-density patch panel with tight port spacing?

Yes, the non-booted design removes the molded boot so the 8P8C plugs seat side-by-side in dense patch panels and keystone jacks without interference.

What is the correct way to seat the non-booted plug, and what mistake should I avoid?

Push the RJ45 straight in until the latch clicks; do not rock or angle the plug, as the bare latch tab can catch on adjacent ports and bend.

How often should I replace a 350 MHz Cat5e cable in a structured cabling run?

Replace only if the jacket is kinked, the latch tab breaks, or certification testing shows insertion-loss or NEXT failures beyond the Cat5e 350 MHz limit.

New to this? Which coin should you pay with — what to check, what it costs to pay, and what is never asked for.

Also in this aisle

People compared these

Same shelf, same checkout — eight coins and a 30-minute rate lock.