We take cryptocurrency — so the coins you hold can buy real hardware.Pay in crypto, spend it on real hardware. Free insured shipping worldwide over $399. Plain, unbranded boxes, sent from Germany.Free insured shipping over $399. Your rate is locked for 30 minutes once checkout opens.Rate locked 30 minutes. Every item sealed, serial-checked and covered by a 24-month warranty.Sealed, 24-month warranty.

Saved items Sign in
Red flat three-wire cable on a spool, 22 AWG tinned copper strands, PVC jacket

AOTOINK AT-3P-100FT 22 AWG 3 Pin Speaker Wire 100ft

SKU CH-51S0-NQDA6

100-foot 22 AWG stranded tinned copper three-conductor cable for low-voltage LED strips and speaker connections

  • ColorRed
  • Length< 1"
  • Connector Number3
  • Connector DetailClassic
  • SpecificationsAOTOINK, 100.0 feet, feet, 22, red, 3, tinned copper, Flat,
  • Wire Gauge22 AWG
  • Premium tin-plated copper ensures efficient conductivity
  • Heat-resistant PVC insulation operates from -30 to 80 degrees Celsius
  • 22 AWG stranded tinned copper wire offers low resistance and flexibility
  • Suitable for WS2812B and WS2811 LED strips up to 24V DC
  • Easy to strip, cut, twist and solder for custom low-voltage installations

Ready-made 100 ft extension for addressable LED

This three-conductor cable uses 22 AWG stranded tinned copper and a flat PVC jacket rated from minus 30 to 80 °C. It is built for WS2812B and WS2811 dream-colour strips as well as general 0-24 V DC loads under 200 W. The wire strips and solders cleanly for quick custom lengths.

Flexible low-voltage link with minimal heat

At 22 AWG the conductors keep resistance low for typical runs powering 5 m of 5050 RGB tape at 60 W or less. The PVC insulation stays supple when routed around corners and does not soften until well above normal operating temperatures. No active cooling or special derating is required for the stated wattage range.

Pre-tinned strands speed up every joint

Each copper strand carries a thin tin coating that wets solder instantly and resists oxidation during storage. The flat three-colour layout keeps polarity obvious when connecting data, power and ground to LED controllers or CB radio gear. Cut, strip and solder — no crimp tools or connectors are bundled.

Highlights

  • Premium tin-plated copper ensures efficient conductivity
  • Heat-resistant PVC insulation operates from -30 to 80 degrees Celsius
  • 22 AWG stranded tinned copper wire offers low resistance and flexibility
  • Suitable for WS2812B and WS2811 LED strips up to 24V DC
  • Easy to strip, cut, twist and solder for custom low-voltage installations

Specifications

BrandAOTOINK
ModelAT-3P-100FT
ColorRed
Length< 1"
Connector Number3
Connector DetailClassic
SpecificationsAOTOINK, 100.0 feet, feet, 22, red, 3, tinned copper, Flat, 3pin-30m-22awg, AT-3P-100FT, Classic
Wire Gauge22 AWG
Shielding3pin-30m-22awg
ConductorStranded 28AWG Tinned Copper
Construction3, tinned copper
Features22, tinned copper, red, 3, Flat, AOTOINK

Questions about this item

How do I connect this 22 AWG stranded tinned copper wire to a WS2812B LED strip?

Strip the flat 3-pin cable, tin the 99.99 % copper strands, then solder to the strip’s 5 V, data and ground pads; the thin tin coating makes soldering easier than with bare copper.

Will the PVC jacket on this 100 ft spool become brittle over time?

The PVC is rated from –30 °C to 80 °C with anti-aging and acid/alkali resistance, so it stays flexible for years in normal indoor or outdoor low-voltage runs.

At what power level does voltage drop become noticeable on a full 100 ft run?

The supplier rates the cable for loads under 200 W at 5–24 V DC; on a 100 ft length, voltage drop on the 22 AWG conductors will be the first limit you hit as wattage approaches that ceiling.

New to this? Which coin should you pay with — what to check, what it costs to pay, and what is never asked for.

Also in this aisle

People compared these

Same shelf, same checkout — eight coins and a 30-minute rate lock.