We take cryptocurrency — so the coins you hold can buy real hardware.Pay in crypto, spend it on real hardware. Free insured shipping worldwide over $399. Plain, unbranded boxes, sent from Germany.Free insured shipping over $399. Your rate is locked for 30 minutes once checkout opens.Rate locked 30 minutes. Every item sealed, serial-checked and covered by a 24-month warranty.Sealed, 24-month warranty.

Saved items Sign in
Two black USB-A male to bare-wire pigtails, 11 inch 18 AWG, red and black leads

Vszerda

Vszerda USB A Male to 2 Pin Bare Wire 11in 18AWG 2-Pack

SKU CH-8FGC-3WZWX

Supplies 5 V power at up to 6 A through an 18 AWG USB-A plug to bare-wire pigtail

  • TypeUSB
  • Terminal GenderMale-to-Male
  • FeaturesFast Charging, DIY 2 Pin Bare Wire
  • Ready for DIY power projects with USB-A male to bare-wire ends
  • 18 AWG pure copper handles up to 6 A at 5 V safely
  • 11 inch length fits tight enclosures and short runs
  • Tinned wire tails simplify soldering or screw-terminal connections
  • Two cables included for spare or dual-device setups

USB A Male to 2 Pin Bare Wire Cable

This 11 inch cable connects a standard USB A port to a bare wire pigtail for DIY power projects. It is built for hobbyists and technicians who need to supply 5 volt power to custom electronics or repair existing USB powered devices. The 2 pack provides a spare for multiple installations or future repairs.

Replaces Damaged or Proprietary Power Leads

Use this cable when a fixed power cord on a USB desk lamp, fan or charging stand fails and the original part is unavailable. The jump is worth it when the device draws up to 6 amps and the bare wire ends allow a direct soldered or screw terminal connection. It is not for builders who need a connectorised plug such as JST, barrel jack or micro USB on the device side.

Sustained 6 Amp Delivery Through 18AWG Conductors

The 18AWG pure copper cores are rated for continuous 5V 6A operation without the voltage sag seen in thinner gauge wires. Double insulated PVC sheathing resists heat and abrasion during long running sessions such as LED strip lighting or cooling fans. Tinned wire tails prevent oxidation and ensure a stable joint whether soldered or clamped under a terminal screw.

Highlights

  • Ready for DIY power projects with USB-A male to bare-wire ends
  • 18 AWG pure copper handles up to 6 A at 5 V safely
  • 11 inch length fits tight enclosures and short runs
  • Tinned wire tails simplify soldering or screw-terminal connections
  • Two cables included for spare or dual-device setups

Specifications

BrandMaixbomr
TypeUSB
Terminal GenderMale-to-Male
FeaturesFast Charging, DIY 2 Pin Bare Wire

Questions about this item

How much clearance do the 11 inch cables need behind a USB A port?

Each cable measures 11 inches (30 cm) from the USB A plug to the bare wire ends, so allow at least that depth behind the port for a straight run.

What is the correct way to solder the tinned 18 AWG leads and which colour is positive?

The red lead is the positive pole and the black lead is the negative pole; both 18 AWG conductors are pre-tinned, so apply heat briefly and feed solder until the joint flows, avoiding excess heat that could melt the PVC insulation.

When should the PVC jacket or bare wire ends be inspected or replaced?

Inspect the double insulated PVC jacket and the tinned wire ends periodically for cracking, discoloration or loose strands; replace the cable if the insulation is damaged or the copper shows corrosion to maintain safe 5 V 6 A operation.

Also in this aisle

People compared these

Same shelf, same checkout — eight coins and a 30-minute rate lock.