We take cryptocurrency — so the coins you hold can buy real hardware.Pay in crypto, spend it on real hardware. Free insured shipping worldwide over $399. Plain, unbranded boxes, sent from Germany.Free insured shipping over $399. Your rate is locked for 30 minutes once checkout opens.Rate locked 30 minutes. Every item sealed, serial-checked and covered by a 24-month warranty.Sealed, 24-month warranty.

Saved items Sign in
Short black cable with a white 4-pin Molex plug branching into two black 15-pin SATA sockets

Vszerda

Vszerda IDE 4Pin to 2 SATA 15Pin Power Extension Cable 15cm

SKU CH-Y1Q8-KY3G0

Converts one 4-pin Molex connector into two SATA power ports for drives and optical devices using a 15 cm Y-splitter

  • TypeSATA
  • Connector TypeSata
  • Cable Length0.4
  • Length0.4
  • Connector Number34
  • Connector DetailSata
  • Powers two SATA drives from one Molex connector
  • 15 cm length keeps cable routing tidy
  • 22 AWG copper conductors deliver reliable current
  • Male-to-female Y-splitter adds ports without new PSU
  • Supports SSDs and optical drives via SATA power

Power Adaptor for Legacy Drives

This Vszerda cable converts a single 4-pin Molex IDE connector into two 15-pin SATA power ports. It lets builders add Serial ATA hard drives or SSDs to a power supply that only offers legacy outputs. The 15 cm Y-splitter keeps cable runs short inside compact enclosures.

Thermals and Power Delivery

Copper conductors at 22 AWG carry the current required by two drives without measurable voltage drop. Passive construction means no fan noise and no extra heat beyond normal resistive loss. The splitter draws power directly from the existing Molex rail, so total load stays within that connector’s rating.

Build and Daily Use

Male-to-female terminals lock securely, preventing accidental disconnection during drive swaps. The short 15 cm length reduces clutter and improves airflow around storage bays. Each SATA head is keyed for correct orientation, so drives seat cleanly every time.

Highlights

  • Powers two SATA drives from one Molex connector
  • 15 cm length keeps cable routing tidy
  • 22 AWG copper conductors deliver reliable current
  • Male-to-female Y-splitter adds ports without new PSU
  • Supports SSDs and optical drives via SATA power

Specifications

Brandchenyang
ModelSA-056
TypeSATA
Connector TypeSata
Cable Length0.4
Length0.4
Connector Number34
Connector DetailSata
Terminal GenderMale-to-Female
ConstructionCopper
FeaturesHi Speed

Questions about this item

How do I install the Vszerda IDE 4Pin to dual SATA 15pin Y splitter and what step do people often get wrong?

Connect the 4-pin Molex male plug from your power supply into the splitter's male end, then attach each 15-pin SATA female connector to your SSD or hard drive. The step people miss is ensuring both SATA connectors click fully into the drive sockets; a loose fit causes intermittent power.

What maintenance or replacement will this 15cm 22AWG power splitter need over time?

No scheduled maintenance is required. Inspect the copper conductors and SATA connectors periodically for dust, oxidation or bent pins. Replace the cable if the insulation cracks, the 4-pin Molex housing deforms, or either SATA female port no longer latches securely to a drive.

What limit appears first when this Y splitter runs two drives under sustained load?

The 22AWG copper wires and 4-pin Molex source connector set the current ceiling. Drawing continuous high current through both SATA branches can heat the cable and cause voltage drop at the drives, so total load should stay within the Molex rail's rated capacity.

Also in this aisle

People compared these

Same shelf, same checkout — eight coins and a 30-minute rate lock.