We take cryptocurrency — so the coins you hold can buy real hardware.Pay in crypto, spend it on real hardware. Free insured shipping worldwide over $399. Plain, unbranded boxes, sent from Germany.Free insured shipping over $399. Your rate is locked for 30 minutes once checkout opens.Rate locked 30 minutes. Every item sealed, serial-checked and covered by a 24-month warranty.Sealed, 24-month warranty.

Saved items Sign in
Black 90-degree UP angled adapter cable with four 8-pin sockets merging into a single 16-pin 12VHPWR plug

Vszerda

Vszerda ATX 8Pin 4 Port to 12VHPWR ATX3.0 PCI-E 5.0 16Pin 90 Degree UP Angled internal power cable

SKU CH-3AVD-XVBW0

Converts four ATX 8-pin outputs into a single 12VHPWR 16-pin connector with a 90-degree upward angle for tight spaces, supporting PCIe 5.0 graphics cards up to 600 W

  • 90-degree upward angle fits tight GPU clearance
  • Four 8-pin ports feed one 16-pin 12VHPWR connector
  • PCIe 5.0 and ATX 3.0 ready for modern graphics cards
  • PCI-SIG H+ spec with 12 power plus 4 signal pins
  • Delivers up to 600W to RTX 40-series and RDNA 3 GPUs

PCIe 5.0 power adapter for new graphics cards

This adapter converts four ATX 8-pin connectors into a single 12VHPWR 16-pin plug that complies with the ATX 3.0 and PCIe 5.0 specifications. It is intended for builders installing RTX 40-series or AMD RDNA 3 graphics cards on power supplies that lack the native connector.

90-degree upward angle eases tight routing

The right-angle design points the cable upward so it fits behind the card even when clearance between the PCB and the side panel is minimal. This geometry reduces strain on the connector and keeps the wire run tidy without forcing sharp bends that can impede airflow.

Delivers up to 600 W through the 12VHPWR interface

The PCI-SIG certified H+ layout provides twelve power pins plus four signal pins on the side, enabling the full 600 W rating defined by the new standard. Systems that cannot supply that level from four 8-pin sources will not meet the card's power requirements.

Highlights

  • 90-degree upward angle fits tight GPU clearance
  • Four 8-pin ports feed one 16-pin 12VHPWR connector
  • PCIe 5.0 and ATX 3.0 ready for modern graphics cards
  • PCI-SIG H+ spec with 12 power plus 4 signal pins
  • Delivers up to 600W to RTX 40-series and RDNA 3 GPUs

Specifications

No published specifications for this item yet.

Questions about this item

How do I install the 90-degree UP angled 12VHPWR adapter so the cable routes cleanly in a tight GPU cut-out?

Plug the four ATX 8-pin connectors fully into the PSU modular ports, then press the 16-pin 12VHPWR end straight into the graphics card socket until the latch clicks; the 90-degree UP bend keeps the cable running parallel to the card instead of protruding outward.

Will the four ATX 8-pin source cables or the 12VHPWR connector need periodic replacement?

The adapter itself has no moving parts or wear items; inspect the pins for discolouration or bent contacts whenever you rebuild the system and reseat both ends if oxidation appears.

At what sustained load does the 600 W-rated 12VHPWR link become the limiting factor?

The PCI-SIG 12VHPWR H+ specification caps continuous delivery at 600 W, so any GPU drawing more than that under prolonged load will hit this connector’s ceiling first.

New to this? Which coin should you pay with — what to check, what it costs to pay, and what is never asked for.

Also in this aisle

People compared these

Same shelf, same checkout — eight coins and a 30-minute rate lock.