We take cryptocurrency — so the coins you hold can buy real hardware.Pay in crypto, spend it on real hardware. Free insured shipping worldwide over $399. Plain, unbranded boxes, sent from Germany.Free insured shipping over $399. Your rate is locked for 30 minutes once checkout opens.Rate locked 30 minutes. Every item sealed, serial-checked and covered by a 24-month warranty.Sealed, 24-month warranty.

Saved items Sign in
Two black USB-A male to bare-wire cables, 22AWG, 1 metre each

Vszerda

Vszerda 2Pcs USB A Male 2 Pin Bare Wire 3FT USB Cable

SKU CH-D5DK-MQQK9

Two USB-A male to bare-wire pigtails with 22 AWG conductors, 5 V / 3 A rating and 480 Mb/s data capability for DIY power or repair jobs

  • TypeUSB
  • Color2Pcs USB A Male to 2 Pin Bare Wire (1M/3FT)
  • Connector Number2
  • Terminal GenderMale-to-Male
  • Speed480 megabits_per_second
  • ConstructionPVC
  • DIY-ready with tinned bare-wire ends for easy soldering
  • Two 3 ft cables included for multiple 5 V / 3 A devices
  • USB 2.0 data transfer at 480 megabits per second
  • 22 AWG pure-copper conductors with double-insulated PVC jacket
  • Red-positive and black-negative colour coding for correct polarity

DIY USB power cable

This two-piece set provides a USB-A male plug on one end and a two-pin bare wire tail on the other for 5 V equipment up to 3 A. It suits makers and technicians who need to install, replace or repair power feeds for low-voltage devices such as LED lamps, USB fans or small appliance lighting. The 22 AWG pure copper conductors deliver reliable conductivity for both power and 480 Mbps data transfer.

PVC jacket with tinned tails

Each cable uses a double-insulated PVC sheath that resists wear and keeps the red positive and black negative leads clearly identified. The pre-tinned wire ends simplify soldering or screw-terminal connections, reducing the chance of loose joints during assembly. At 1 m length the leads reach typical bench or enclosure layouts without excess slack.

Replaces damaged factory leads

The assembly upgrades frayed or missing original cables on 5 V/3 A gear including desk lamps, charging stands, socket panels and circuit-board power inputs. The jump is worthwhile when the original moulded connector has failed or when a custom length and bare-wire termination are required for a permanent installation.

Highlights

  • DIY-ready with tinned bare-wire ends for easy soldering
  • Two 3 ft cables included for multiple 5 V / 3 A devices
  • USB 2.0 data transfer at 480 megabits per second
  • 22 AWG pure-copper conductors with double-insulated PVC jacket
  • Red-positive and black-negative colour coding for correct polarity

Specifications

BrandMaixbomr
TypeUSB
Color2Pcs USB A Male to 2 Pin Bare Wire (1M/3FT)
Connector Number2
Terminal GenderMale-to-Male
Speed480 megabits_per_second
ConstructionPVC
FeaturesData Transfer

Questions about this item

Does the USB-A plug support USB 2.0 data rates of 480 megabits per second?

Yes, the cable is rated for 480 megabits per second, which matches the USB 2.0 high-speed standard.

What wire gauge and length must I plan for when routing this cable inside a device?

The conductors are 22 AWG and the overall length is 1 metre, or 3 feet.

How do I connect the bare-wire end without damaging the conductors?

The red and black wires are pre-tinned; strip only the minimum insulation needed, then solder or screw them to the 5 V positive and negative terminals.

Also in this aisle

People compared these

Same shelf, same checkout — eight coins and a 30-minute rate lock.