We take cryptocurrency — so the coins you hold can buy real hardware.Pay in crypto, spend it on real hardware. Free insured shipping worldwide over $399. Plain, unbranded boxes, sent from Germany.Free insured shipping over $399. Your rate is locked for 30 minutes once checkout opens.Rate locked 30 minutes. Every item sealed, serial-checked and covered by a 24-month warranty.Sealed, 24-month warranty.

Saved items Sign in
ViewSonic PJD6353 replacement projector lamp module with 180W Osram P-VIP bulb in housing

ViewSonic

ViewSonic PJD6353 OEM Replacement Projector Lamp 180W Osram P-VIP 180W Bulb Housing RLC-077

SKU CH-XSF7-B3A7Y

Replacement projector lamp module with 180 W Osram P-VIP bulb and housing, rated 3,500 normal or 5,000 economy hours

  • TypeProjector Lamp
  • Wattage180W
  • Lamp Life3,500 (Normal) - 5,000 (Economy) Hrs.
  • Ready to install with pre-assembled bulb and housing
  • 180W Osram P-VIP lamp delivers reliable brightness
  • 3,500 hours normal mode or 5,000 hours economy mode
  • Manufactured to ISO 9001 quality standards
  • Fits ViewSonic PJD6353 projectors using RLC-077 module

Direct replacement for PJD6353 projectors

This 180W replacement lamp module fits the ViewSonic PJD6353 and uses the manufacturer part number RLC-077. It ships as a complete bulb-and-housing assembly so the projector is ready to run immediately after the swap. The lamp is built with a genuine Osram P-VIP bulb manufactured to ISO 9001 quality standards. It is intended for owners who need a factory-specification light source without modification.

Restores original brightness after the old lamp dims

Replace the module when the existing lamp reaches the end of its rated life or when image brightness drops below usable levels. In normal mode the lamp is rated for 3,500 hours and in economy mode for 5,000 hours, so the upgrade is worth it when the current unit no longer meets those targets. The part is not suited for users who require a different wattage or a non-OEM form factor.

Tool-free swap in minutes

Installation consists of opening the projector lamp door, removing the old module and sliding the new assembly into place until it seats firmly. No wiring or alignment adjustments are required because the housing matches the original mounting points. The most common issue is forgetting to reset the projector lamp-hour counter after installation, which can cause premature replacement warnings.

Highlights

  • Ready to install with pre-assembled bulb and housing
  • 180W Osram P-VIP lamp delivers reliable brightness
  • 3,500 hours normal mode or 5,000 hours economy mode
  • Manufactured to ISO 9001 quality standards
  • Fits ViewSonic PJD6353 projectors using RLC-077 module

Specifications

BrandViewSonic
TypeProjector Lamp
Wattage180W
Lamp Life3,500 (Normal) - 5,000 (Economy) Hrs.

Questions about this item

Which ViewSonic projector models accept the RLC-077 lamp housing?

The RLC-077 module is built for the ViewSonic PJD6353 projector and matches the original housing dimensions for direct fit.

What is the correct sequence to install the 180W Osram P-VIP bulb module?

Power off and cool the projector, remove the lamp cover, release the securing screws, slide out the old unit, insert the new RLC-077 housing until it seats firmly, retighten screws, replace the cover, then reset the lamp timer in the menu.

When should the Osram P-VIP 180W bulb be replaced based on rated hours?

Plan replacement around 3,500 hours in Normal mode or 5,000 hours in Economy mode, as brightness drops to half at those points.

Also in this aisle

People compared these

Same shelf, same checkout — eight coins and a 30-minute rate lock.