We take cryptocurrency — so the coins you hold can buy real hardware.Pay in crypto, spend it on real hardware. Free insured shipping worldwide over $399. Plain, unbranded boxes, sent from Germany.Free insured shipping over $399. Your rate is locked for 30 minutes once checkout opens.Rate locked 30 minutes. Every item sealed, serial-checked and covered by a 24-month warranty.Sealed, 24-month warranty.

Saved items Sign in
VEVOR stud welder dent repair kit in organiser box with slide hammer and accessories

VEVOR

VEVOR Stud Welder Dent Repair Kit 1800W 7 Modes

SKU CH-BXS1-G4X64

Spot welding dent puller with seven modes for carbon steel, stainless steel and iron, includes organiser box, slide hammer, 30 studs and assorted washers and tabs

  • TypeOther Appliances
  • Width11.02
  • 1800W output powers through carbon steel, stainless steel and iron
  • Seven selectable modes match the weld to each dent repair task
  • 30 M4 iron studs plus assorted washers and pulling tabs included
  • Slide hammer, suction cup and puller attachments enable multiple pulling techniques
  • Compact 310 x 275 x 245 mm frame fits tight workshop spaces

Purpose and User

The VEVOR Stud Welder Dent Repair Kit is a 1800W spot welding machine designed for pulling dents from vehicle panels. It ships with seven selectable welding modes and a full accessory set including slide hammer, wiggle wires, collets, carbon rods, puller attachments, suction cup and assorted washers, studs and tabs. The unit weighs 43.21 lbs and measures 12.2 x 10.8 x 9.6 inch.

Setup Requirements

Verify that your workshop supply can deliver 1800W at the required voltage and that the circuit breaker and wiring are rated for the load. Confirm you have adequate bench space for the 12.2 x 10.8 inch footprint and clearance for the 9.6 inch height. Ensure you can store the 43.21 lb unit safely and that ventilation suits prolonged welding cycles.

Suitability

This kit suits automotive technicians and restoration hobbyists who need a complete manual-adjustment stud welder for carbon steel, stainless steel and iron panels. It is not for buyers who require automated welding programmes, aluminium-only capability, a lighter portable unit or a machine with a smaller footprint than 310 x 275 x 245 mm.

Highlights

  • 1800W output powers through carbon steel, stainless steel and iron
  • Seven selectable modes match the weld to each dent repair task
  • 30 M4 iron studs plus assorted washers and pulling tabs included
  • Slide hammer, suction cup and puller attachments enable multiple pulling techniques
  • Compact 310 x 275 x 245 mm frame fits tight workshop spaces

Specifications

TypeOther Appliances
Width11.02

Questions about this item

What accessories come in the box and is anything needed separately?

The kit includes an organiser box, slide hammer, 10 wiggle wires, stud collet, carbon rod collet, washer collet, 2 carbon rods, wrench, puller hook, puller claw, 10 triangle washers, 10 pulling tabs, 20 round washers, suction cup, suction cup nut, 30 iron studs M4, stud collet M4 and a user manual.

Which welding mode should I choose for carbon steel, stainless steel or iron?

The welder offers 7 selectable modes with manual adjustment; choose the mode that matches the material thickness and type you are repairing.

How does the 1800W rating affect performance on a typical car panel?

The 1800W output delivers enough heat to weld M4 studs and carbon rods into carbon steel, stainless steel and iron panels for dent pulling.

Also in this aisle

People compared these

Same shelf, same checkout — eight coins and a 30-minute rate lock.