We take cryptocurrency — so the coins you hold can buy real hardware.Pay in crypto, spend it on real hardware. Free insured shipping worldwide over $399. Plain, unbranded boxes, sent from Germany.Free insured shipping over $399. Your rate is locked for 30 minutes once checkout opens.Rate locked 30 minutes. Every item sealed, serial-checked and covered by a 24-month warranty.Sealed, 24-month warranty.

Saved items Sign in
Black braided fuel hose coil with twelve anodised aluminium swivel fittings in straight, forty-five

VEVOR

VEVOR 8AN Fuel Line Kit 20 ft 0.43 in 12 PCS Swivel Fitting Adapter Kit Black

SKU CH-GGR5-4A55Q

20 ft braided fuel hose with 12 swivel adapters rated 500 psi working pressure from -40°F to 257°F

  • TypeOther Appliances
  • Width9.06
  • Handles 500 psi working pressure with 2000 psi burst rating
  • Operates from -40 °F to 257 °F for extreme conditions
  • 20 ft length with 0.43 in inner diameter for ample flow
  • 12-piece swivel fitting kit includes straight 45 90 180 degree ends
  • Triple-layer nylon stainless CPE construction resists wear and pressure

Automotive Fuel System Kit

This 8AN fuel line kit delivers 20 feet of braided hose with twelve swivel fittings for custom routing in fuel, oil and transmission cooler circuits. The CPE rubber inner tube handles gasoline, diesel and transmission fluid while the nylon and stainless steel braid resists abrasion. Builders assembling hot-rod, race or restoration fuel systems will find the components match common 8AN plumbing requirements.

Swivel Fittings and Sealing Kit

Four straight, two 45 degree, two 90 degree and two 180 degree swivel hose ends let you navigate tight engine bays without kinking the line. Ten sealing rings are included to refresh every joint during assembly. Two hose separators keep parallel runs organised and prevent chafing. An instruction manual guides torque sequence and hose-end installation for leak-free results.

Pressure and Temperature Envelope

The hose is rated for 500 psi maximum working pressure and 2000 psi burst pressure, covering high-pressure EFI and returnless systems. Continuous operation spans -40°F to 257°F, so the line survives cold starts and sustained track heat. The 0.43 inch inner diameter supports adequate flow for most street and strip pumps, but builders chasing extreme horsepower may need larger bore lines. The kit excludes E85 compatibility.

Highlights

  • Handles 500 psi working pressure with 2000 psi burst rating
  • Operates from -40 °F to 257 °F for extreme conditions
  • 20 ft length with 0.43 in inner diameter for ample flow
  • 12-piece swivel fitting kit includes straight 45 90 180 degree ends
  • Triple-layer nylon stainless CPE construction resists wear and pressure

Specifications

TypeOther Appliances
Width9.06

Questions about this item

How often should the sealing rings on the 12 swivel fittings be inspected and replaced?

The kit includes 10 sealing rings for the swivel fittings; inspect them during routine fuel system checks and replace any that show cracking or flattening to maintain the 500 psi working pressure seal.

Which temperature limit will the CPE rubber inner layer reach first during continuous engine-bay operation?

The hose is rated to 257 °F; sustained temperatures above that level will degrade the inner layer before the 2000 psi burst margin becomes a factor.

How much heat does the 20 ft braided line radiate when fuel circulates all day at 500 psi?

The nylon and stainless steel braid acts as insulation, so surface temperature stays close to the fluid temperature up to the 257 °F rating without adding significant radiant heat to surrounding components.

Also in this aisle

People compared these

Same shelf, same checkout — eight coins and a 30-minute rate lock.