We take cryptocurrency — so the coins you hold can buy real hardware.Pay in crypto, spend it on real hardware. Free insured shipping worldwide over $399. Plain, unbranded boxes, sent from Germany.Free insured shipping over $399. Your rate is locked for 30 minutes once checkout opens.Rate locked 30 minutes. Every item sealed, serial-checked and covered by a 24-month warranty.Sealed, 24-month warranty.

Saved items Sign in
Steel pneumatic oil extractor tank on wheels with hoses and probes

VEVOR

VEVOR 5 Gallon Pneumatic Waste Oil Extractor Drain Tank

SKU CH-WEZ8-Y9WZ6

A 22.7 L steel tank uses 8-10 bar air pressure and six probes to extract waste oil with a safety valve and 1.5 m hoses

  • Width13.78
  • 7 L steel tank reduces emptying frequency during waste oil collection
  • Six suction probes reach reservoir bottom to extract every drop of fluid
  • Safety valve prevents overpressure while closed-loop design limits environmental contact
  • 9-inch rear wheels and portable handle enable easy workshop manoeuvring
  • 5 m discharge and suction hoses provide flexible reach around the vehicle

5 Gallon Pneumatic Oil Extractor

The VEVOR 5 gallon pneumatic waste oil extractor uses compressed air at 8-10 bar to create vacuum suction for draining motor oil from vehicle reservoirs. Its 22.7 litre steel tank stores collected fluid until disposal, while a safety valve prevents overpressure during operation. The unit suits workshops and mobile technicians who need portable fluid extraction without electrical power.

Upgrade From Manual Gravity Drain

This extractor replaces gravity drain pans and hand pump units by using shop air to pull oil through dipstick tubes or drain ports. The jump is worth it when you service multiple vehicles per day and want faster turnaround with less physical effort. It is not for buyers who only change oil occasionally or lack a compressed air supply capable of 200 L per minute flow.

Setup With Included Probes And Hoses

The package includes two metal hoses at 27.6 inches, four nylon tubes ranging from 28.0 to 33.9 inches, and six suction probes that reach the bottom of reservoirs. Connect the discharge and suction hoses at 59 inches each, set air pressure, and monitor the visible level indicator. What usually goes wrong is mismatched probe diameter for a specific dipstick tube, so verify the 0.24 inch and 0.32 inch metal hose options fit before starting.

Highlights

  • 7 L steel tank reduces emptying frequency during waste oil collection
  • Six suction probes reach reservoir bottom to extract every drop of fluid
  • Safety valve prevents overpressure while closed-loop design limits environmental contact
  • 9-inch rear wheels and portable handle enable easy workshop manoeuvring
  • 5 m discharge and suction hoses provide flexible reach around the vehicle

Specifications

Width13.78

Questions about this item

What width clearance does the 13.78 in extractor need with its 5.9 in rear wheels?

The unit is 13.78 in wide; allow at least that much space plus room for the 5.9 in rear wheels to swivel and for the 59 in discharge and suction hoses to extend without kinking.

Which step is often missed when hooking the extractor to an 8-10 bar air supply?

Users sometimes forget to verify the supply pressure stays within 8-10 bar before opening the valve; the safety valve will vent if pressure exceeds the limit, so confirm regulator setting first.

What parts will need replacement after repeated waste-oil changes?

The 59 in suction and discharge hoses, the four nylon tubes (8 x 0.9 x 710 mm, 6 x 0.9 x 860 mm) and the two metal hoses (8 x 0.3 x 700 mm, 6 x 0.3 x 700 mm) can wear or crack over time and should be inspected each use.

Also in this aisle

People compared these

Same shelf, same checkout — eight coins and a 30-minute rate lock.