We take cryptocurrency — so the coins you hold can buy real hardware.Pay in crypto, spend it on real hardware. Free insured shipping worldwide over $399. Plain, unbranded boxes, sent from Germany.Free insured shipping over $399. Your rate is locked for 30 minutes once checkout opens.Rate locked 30 minutes. Every item sealed, serial-checked and covered by a 24-month warranty.Sealed, 24-month warranty.

Saved items Sign in
Red hydraulic transmission jack on four swivel wheels with telescopic lift arm and foot pedal

VEVOR

VEVOR 1322REDJACK 1322 lbs Transmission Jack specialty appliance

SKU CH-N0ZA-J4326 MPN 1322REDJACK

A hydraulic telescopic transmission jack lifts up to 1322 lbs with a 33.5 to 67 inch range, 360 degree saddle rotation, 30 degree tilt, foot pedal operation and 360 degree swivel wheels

  • TypeOther
  • Lifts heavy transmissions with 1322 lbs hydraulic capacity
  • Extends from 33.5 to 67 inches for varied vehicle heights
  • 360-degree saddle rotation plus 30-degree tilt for precise alignment
  • Four 360-degree swivel wheels move the jack easily around the shop
  • Strong steel frame weighs 95.9 lbs for stable, durable lifting

1322 lbs Hydraulic Transmission Jack

The VEVOR 1322REDJACK is a 1322 lbs capacity hydraulic telescopic jack built for removing and installing transmissions in garage or shop environments. Its two-stage design extends from 33.5 inches to 67 inches, giving the reach needed for under-vehicle work. The fully adjustable saddle rotates 360 degrees and tilts 30 degrees for precise alignment. Four 360-degree swivel wheels let you manoeuvre the 95.9 lb steel frame into position.

Replaces Fixed-Height Stands

This jack upgrades from static transmission cradles that cannot match varying lift points or saddle angles. The telescopic range and adjustable saddle make the jump worthwhile when you service different vehicle platforms or need fine tilt control during installation. The 23-3/5 inch safety chain secures the load once positioned. Buyers who only work on a single vehicle with a known lift height may not need the adjustable range.

Floor-Rolling Assembly Required

The unit ships as a steel frame with wheels, pedal pump and saddle components that bolt together using common hand tools. No hydraulic bleeding is needed because the system arrives pre-filled. The most common issue is aligning the saddle pivot bolts during final tightening — work on level ground and torque evenly to avoid binding. The wide 25.6 inch base resists tipping, but always chock the wheels before raising a load.

Highlights

  • Lifts heavy transmissions with 1322 lbs hydraulic capacity
  • Extends from 33.5 to 67 inches for varied vehicle heights
  • 360-degree saddle rotation plus 30-degree tilt for precise alignment
  • Four 360-degree swivel wheels move the jack easily around the shop
  • Strong steel frame weighs 95.9 lbs for stable, durable lifting

Specifications

TypeOther

Questions about this item

How much floor space does the 33.5" x 25.6" base need?

The jack occupies a 33.5 inch by 25.6 inch footprint. Allow extra clearance around the 360 degree swivel wheels so the unit can be rolled into position under the vehicle.

What is the correct sequence for using the foot pedal and the safety chain?

Position the saddle under the transmission, pump the foot pedal to raise the load, then secure the 23-3/5 inch safety chain around the component before lowering or moving the jack.

When should the hydraulic fluid be checked on a 1322 lbs capacity telescopic jack?

Inspect the fluid level if the saddle travels the full 33-1/2 to 67 inch range slowly or feels spongy. Top up with the recommended hydraulic oil and bleed air from the system.

Also in this aisle

People compared these

Same shelf, same checkout — eight coins and a 30-minute rate lock.