We take cryptocurrency — so the coins you hold can buy real hardware.Pay in crypto, spend it on real hardware. Free insured shipping worldwide over $399. Plain, unbranded boxes, sent from Germany.Free insured shipping over $399. Your rate is locked for 30 minutes once checkout opens.Rate locked 30 minutes. Every item sealed, serial-checked and covered by a 24-month warranty.Sealed, 24-month warranty.

Saved items Sign in
13 lb galvanised fluke anchor kit with 7.9 ft chain, 101 ft rope, two 0.4 in shackles

VEVOR

VEVOR 13 lb Fluke Anchor Kit 7.9' Chain 101' Rope 2 Shackles

SKU CH-QKK6-6MPFZ

A 13 lb fluke anchor kit with 7.9' chain, 101' nylon rope and two 0.4" shackles for vessels 21 to 30 ft

  • TypeOther Appliances
  • Width18.11
  • Complete 13 lb anchor kit with chain rope and two shackles included
  • Hot-dipped galvanized steel construction resists corrosion in marine environments
  • Self-aligning fluke design digs quickly into mud sand and silt bottoms
  • 9 ft chain and 101 ft nylon rope suit vessels up to 30 ft
  • Two 0.4 in shackles provide secure connection points for deployment

What the kit is and who it serves

This 13 lb fluke anchor kit includes a hot-dipped galvanized steel anchor, a 7.9' chain, a 101' nylon rope, and two 0.4" shackles. It is intended for small vessels between 21 and 30 ft such as sailboats, fishing boats, speedboats, and small yachts. The complete package removes the need to source separate components. Buyers needing ground tackle for larger craft or heavier displacement will find this kit insufficient.

Practical limits of the fluke design

The anchor weighs 13 lbs with a fluke thickness of 0.4" and a plate thickness of 0.2". Its low centre of gravity and self-aligning geometry help it set quickly in soft mud, sand, and silt. The 7.9' chain adds weight at the crown to improve the angle of pull. Performance drops on hard bottoms, rock, or thick weed where the flukes cannot penetrate. The 101' rope length suits typical inshore depths but may fall short in deeper anchorages.

Installation experience and common issues

The kit arrives ready to assemble: attach the chain to the anchor crown, connect the rope via the thimble and shackles, then secure the bitter end to the boat. The two 0.4" shackles (pin 0.4", ring 0.4") fit the supplied chain and rope eyes. The included manual illustrates the steps. A frequent oversight is failing to seize the shackle pins with wire or cable ties, which can back out under cyclic loads. Another common error is using too little scope for the conditions, reducing holding power.

Highlights

  • Complete 13 lb anchor kit with chain rope and two shackles included
  • Hot-dipped galvanized steel construction resists corrosion in marine environments
  • Self-aligning fluke design digs quickly into mud sand and silt bottoms
  • 9 ft chain and 101 ft nylon rope suit vessels up to 30 ft
  • Two 0.4 in shackles provide secure connection points for deployment

Specifications

TypeOther Appliances
Width18.11

Questions about this item

Should I choose the 13 lb anchor or a different weight for my 21 to 30 ft boat?

The kit supplies a 13 lb fluke anchor intended for vessels from 21 to 30 ft, so this single weight covers the stated range.

How does the 13 lb fluke anchor perform once it hits the seabed?

Its low centre of gravity and self‑aligning geometry let the two sharp jaws rotate and dig into mud, sand, silt or soft mud for a secure hold.

What does the 0.4 inch shackle size mean for my rode connection?

Both the shackle ring and pin measure 0.4 inch, matching the chain and rope ends supplied in the kit for a direct fit.

Also in this aisle

People compared these

Same shelf, same checkout — eight coins and a 30-minute rate lock.