We take cryptocurrency — so the coins you hold can buy real hardware.Pay in crypto, spend it on real hardware. Free insured shipping worldwide over $399. Plain, unbranded boxes, sent from Germany.Free insured shipping over $399. Your rate is locked for 30 minutes once checkout opens.Rate locked 30 minutes. Every item sealed, serial-checked and covered by a 24-month warranty.Sealed, 24-month warranty.

Saved items Sign in
Red one-piece LED tail light for 1955 Chevy, rectangular polycarbonate lens, sealed epoxy housing, 1157 connector

United Pacific Industries

United Pacific Industries 110206 One-Piece LED Tail Light 1955 Chevy

SKU CH-Z2S6-EB7YF

One-piece LED tail light for 1955 Chevy with 48 SMD LEDs, sealed epoxy electronics and direct 1157 plug-in installation

  • TypeTail Lights
  • QualityGenuine OEM
  • Direct plug-and-play fit using the factory 1157 connector
  • 48 SMD LEDs deliver a super-bright red signal
  • One-piece polycarbonate lens resists moisture and corrosion
  • Solid-state board runs reliably on any 12 V system
  • Lightweight 0.57 lb housing simplifies installation on a 1955 Chevy

Direct-Fit LED Tail Light for 1955 Chevy

This one-piece LED tail light replaces the original assembly on a 1955 Chevrolet with a direct plug-and-play 1157 connector. It uses 48 SMD LEDs behind an all-red polycarbonate lens and runs on any 12 VDC system. The electronics are sealed in epoxy to resist moisture and corrosion. Buyers needing a factory backup-light function will not find it here.

Thermal and Electrical Behaviour

Solid-state circuitry produces minimal heat draw compared with incandescent units and places very low load on the vehicle’s charging system. No fan or active cooling is required because the sealed epoxy construction dissipates heat passively. The lamp operates silently and eliminates the flicker that can occur with aged mechanical flashers. An upgraded LED-compatible flasher such as item 90652 or 90649 is recommended for correct blink rate.

Installation and Companion Parts

The 10.2 x 5.35 x 3 inch housing weighs .57 lbs and bolts into the stock location without modification. Because the backup-light lens is deleted, a separate LED licence-plate lamp with backup function — item 50187 — is suggested to restore rear illumination. No additional wiring harnesses, resistors or control modules are needed beyond the recommended flasher upgrade.

Highlights

  • Direct plug-and-play fit using the factory 1157 connector
  • 48 SMD LEDs deliver a super-bright red signal
  • One-piece polycarbonate lens resists moisture and corrosion
  • Solid-state board runs reliably on any 12 V system
  • Lightweight 0.57 lb housing simplifies installation on a 1955 Chevy

Specifications

TypeTail Lights
QualityGenuine OEM

Questions about this item

How do I install the 110206 one-piece LED tail light on my 1955 Chevy, and what is the step people often miss?

Connect the 1157 type connector directly for plug-and-play installation; the step many miss is upgrading the under-dash flasher to item 90652 or 90649 so the LED circuit flashes correctly.

What maintenance or replacement will the 110206 tail light need later?

The electronics are sealed in epoxy on a solid-state circuit board, so no bulb changes are needed; only the external 1157 connector or a failed flasher unit would ever require replacement.

What limit appears first on the 110206 tail light during sustained use?

The solid-state board is engineered for any 12VDC system, and the epoxy-sealed 48 SMD LEDs resist heat and moisture, so no thermal or electrical limit is reached under normal continuous operation.

Also in this aisle

People compared these

Same shelf, same checkout — eight coins and a 30-minute rate lock.