We take cryptocurrency — so the coins you hold can buy real hardware.Pay in crypto, spend it on real hardware. Free insured shipping worldwide over $399. Plain, unbranded boxes, sent from Germany.Free insured shipping over $399. Your rate is locked for 30 minutes once checkout opens.Rate locked 30 minutes. Every item sealed, serial-checked and covered by a 24-month warranty.Sealed, 24-month warranty.

Saved items Sign in
Silver aluminium block resistor with white nylon leads and solder lug terminals, 32 x 6 x 2.8 cm

Unique-Bargains

Unique-Bargains Aluminium Housing Braking Resistor 1000W 8 Ohm

SKU CH-ZMG4-XA6TA

An aluminium-housed 1000 W 8 Ω braking resistor with solder-lug terminals and nylon-wrapped leads for power-supply, transducer or elevator installations

  • FeaturesBraking Resistor;Aluminium Housing Braking Resistor;Solder L
  • High-power 1000 W rating handles heavy braking loads
  • 8 Ω resistance with ±5 % tolerance matches drive specs
  • Aluminium housing dissipates heat for severe-environment cooling
  • Solder-lug terminals on nylon-wrapped 46 cm leads simplify wiring
  • Compact 32 × 6 × 2.8 cm footprint fits tight panels

1000 W Aluminium Braking Resistor

This 1000 W aluminium housed braking resistor dissipates regenerative energy in motor drives, elevators and power supplies. Its silver tone aluminium body mounts directly to a cooling plate for reliable operation in severe environments. The unit weighs 997 g and measures 32 x 6 x 2.8 cm overall.

8 Ω ±5 % with 1000 W rating

The 8 ohm resistance handles continuous braking loads up to the full 1000 W rating, while the ±5 % tolerance keeps performance predictable. Nylon wrapped leads and solder lug terminals simplify wiring in tight cabinets. Heat capacity runs out when dissipation exceeds the rated wattage without additional forced cooling.

Solder lug terminals for direct wiring

Each terminal has an outer diameter of 8.5 mm and an inner diameter of 4 mm, accepting ring or fork lugs without adapters. The 46 cm long, 0.3 cm diameter nylon wrapped wires reach most panel layouts. Builders needing plug connectors or different wire lengths must add their own termination.

Highlights

  • High-power 1000 W rating handles heavy braking loads
  • 8 Ω resistance with ±5 % tolerance matches drive specs
  • Aluminium housing dissipates heat for severe-environment cooling
  • Solder-lug terminals on nylon-wrapped 46 cm leads simplify wiring
  • Compact 32 × 6 × 2.8 cm footprint fits tight panels

Specifications

BrandUnique Bargains
FeaturesBraking Resistor;Aluminium Housing Braking Resistor;Solder Lug Terminals;Nylon Wrapped Wire;40 Ohm Resistor

Questions about this item

Will the 32 cm aluminium housing fit on the cooling plate I already use for my 8 ohm load bank?

The housing measures 32 x 6 x 2.8 cm and is designed for cooling-plate mounting, so it will match the same footprint as other 32 cm aluminium-cased resistors.

How can I verify the resistor is operating within its 1000 W rating after wiring the solder lug terminals?

Measure the voltage across the 8 ohm terminals under load; the resistor is working correctly when the dissipated power calculated from that voltage stays at or below 1000 W and the aluminium case temperature stabilises.

Does the package include the nylon-wrapped leads and solder lug terminals, or must I source cables separately?

The box contains one complete braking resistor with the 46 cm nylon-wrapped wires and 4 x 8.5 mm solder lug terminals already attached; no additional cables are required.

Also in this aisle

People compared these

Same shelf, same checkout — eight coins and a 30-minute rate lock.