We take cryptocurrency — so the coins you hold can buy real hardware.Pay in crypto, spend it on real hardware. Free insured shipping worldwide over $399. Plain, unbranded boxes, sent from Germany.Free insured shipping over $399. Your rate is locked for 30 minutes once checkout opens.Rate locked 30 minutes. Every item sealed, serial-checked and covered by a 24-month warranty.Sealed, 24-month warranty.

Saved items Sign in
Black sleeved PWM fan hub splitter cable with one 4-pin female to five 4-pin male connectors, 15.7 inch length

ThreeBulls 1-to-5 PWM Fan Hub Splitter Cable 15.7 Inch

SKU CH-V5WB-XQ6DN

Connects one motherboard header to five PWM or 3-pin fans using a 15.7-inch sleeved cable

  • Type1 to 5,1 Pack
  • Color1 to 5,1 Pack
  • Connector Detail4 Pin/3pin to Male-to-Female
  • Terminal GenderMale to Female
  • Specifications1 to 5,1 Pack, 15.7 L x 0.7 W x 0.2 H inches
  • Shielding1 to 5,1 Pack
  • Connect up to five fans from a single motherboard header
  • Supports both 4-pin PWM and 3-pin fan connectors
  • 7 inch length gives flexible routing inside the case
  • Black braided sleeving protects wires and keeps the build tidy
  • Male-to-female design plugs directly between board and coolers

PWM fan hub for desktop builds

This ThreeBulls splitter connects one motherboard header to five case or CPU fans using a single 4-pin PWM source. The 15.7 inch sleeved cable keeps routing tidy inside standard ATX and micro-ATX chassis. It suits builders adding multiple intake or exhaust fans without extra headers.

Practical limits of the 4-pin PWM interface

The hub passes one PWM control signal to all five outputs so every connected fan runs at the same duty cycle. Three-pin fans receive constant 12 V power and cannot be speed-controlled through this adapter. Total current draw must stay within the motherboard header rating.

Single 4-pin male header supplies all five fans

The splitter draws power from one 4-pin male plug on the board, distributing it across five female connectors. If the combined fan current exceeds the header limit, the system may throttle or shut down. Builders needing independent speed curves or higher aggregate current should use a powered hub instead.

Highlights

  • Connect up to five fans from a single motherboard header
  • Supports both 4-pin PWM and 3-pin fan connectors
  • 7 inch length gives flexible routing inside the case
  • Black braided sleeving protects wires and keeps the build tidy
  • Male-to-female design plugs directly between board and coolers

Specifications

BrandThreeBulls
Type1 to 5,1 Pack
Color1 to 5,1 Pack
Connector Detail4 Pin/3pin to Male-to-Female
Terminal GenderMale to Female
Specifications1 to 5,1 Pack, 15.7 L x 0.7 W x 0.2 H inches
Shielding1 to 5,1 Pack
ConductorPolycarbonate
ConstructionCoaxial
Features1 to 5,1 Pack
Disclaimernot_applicable

Questions about this item

How many fans can I connect with the 1-to-5 splitter?

The hub splits a single 4-pin header into five connectors, so you can run up to five PWM or voltage-controlled fans from one motherboard socket.

Will the 15.7-inch length reach from my motherboard fan header to the top or rear case mounts?

At 15.7 inches the sleeved cable spans most mid-tower layouts, giving enough slack to route behind the motherboard tray to top, rear or front fan positions.

Does the 4-pin PWM header on the splitter pass speed control to 3-pin fans as well?

The splitter carries the PWM signal to all five ports; 4-pin fans receive full PWM control while 3-pin fans run at variable voltage governed by the same header.

New to this? Which coin should you pay with — what to check, what it costs to pay, and what is never asked for.

Also in this aisle

People compared these

Same shelf, same checkout — eight coins and a 30-minute rate lock.