We take cryptocurrency — so the coins you hold can buy real hardware.Pay in crypto, spend it on real hardware. Free insured shipping worldwide over $399. Plain, unbranded boxes, sent from Germany.Free insured shipping over $399. Your rate is locked for 30 minutes once checkout opens.Rate locked 30 minutes. Every item sealed, serial-checked and covered by a 24-month warranty.Sealed, 24-month warranty.

Saved items Sign in
Black sleeved 4-pin PWM fan splitter cable with one female and three male connectors 27cm 10.5 inches

THE ORDINARY

THE ORDINARY 4Pin 1 to 3 PWM Fan Splitter Cable Black Sleeved 27cm 10.5 inches

SKU CH-PYP0-PG5GY

Connects three PWM fans to one motherboard header with speed control via a 27 cm black-sleeved 24 AWG cable

  • ColorBlack
  • Features4Pin 1 to 3 Ways PWM Fan Splitter Cable, to realize 3 fans p
  • Connect three fans to one motherboard header for PWM speed control
  • High-density black sleeved 24 AWG cable resists wear and keeps wiring tidy
  • Single yellow RPM wire reports one fan speed to avoid motherboard confusion
  • Works with both 3-pin and 4-pin fans for broad compatibility
  • 27 cm (10.5 inches) length extends the 4-pin header for flexible routing

PWM splitter for triple-fan control

This black-sleeved cable splits a single motherboard 4-pin header into three 4-pin fan connectors, letting three fans share one PWM speed-control signal. It is built for PC builders who want tidy cable routing and synchronised fan speeds without occupying extra headers.

Single tachometer wire avoids sensor confusion

Only one of the three output connectors carries the yellow RPM reporting line, so the motherboard sees a single speed reading instead of three conflicting ones. The 24AWG sleeved wires keep the bundle flexible and resistant to abrasion inside a crowded case.

Works with 3-pin and 4-pin fans at 27 cm length

The 27 cm (10.5 inches) reach lets you route from a CPU or chassis header to nearby fans without strain. Compatibility with both 3-pin and 4-pin fans means older voltage-controlled models can also be powered, though they will run at full speed without PWM regulation.

Highlights

  • Connect three fans to one motherboard header for PWM speed control
  • High-density black sleeved 24 AWG cable resists wear and keeps wiring tidy
  • Single yellow RPM wire reports one fan speed to avoid motherboard confusion
  • Works with both 3-pin and 4-pin fans for broad compatibility
  • 27 cm (10.5 inches) length extends the 4-pin header for flexible routing

Specifications

ColorBlack
Features4Pin 1 to 3 Ways PWM Fan Splitter Cable, to realize 3 fans powered by 1 interface with speed regulation. High quality high density black sleeved cable, 24AWG, length is approx. 27cm / 10.5 inches. The fan adapter has only one connector with a yellow RPM speed/tachometer line. Make the motherboard receive only one fan RPM speed reading without being confused by multiple fan readings. The cable is compatible with 3-pin and 4-pin PC fans. Can be used for a motherboard 4pin interface powering for multiple cooling fans and PWM speed control, lengthen and extend the motherboard 4-pin inter

Questions about this item

Will the yellow RPM wire on this splitter ever need replacing?

The yellow RPM wire is soldered into the single reporting connector and cannot be swapped independently; if it fails the whole 24AWG sleeved assembly must be replaced.

What stops me from running more than three fans off one header with this cable?

The splitter provides exactly three 4-pin male ends, so the physical connector count is the hard limit.

Does the black sleeving trap heat when three fans run all day?

The 24AWG conductors and open-air sleeving dissipate the low PWM control current without noticeable temperature rise.

New to this? Which coin should you pay with — what to check, what it costs to pay, and what is never asked for.

Also in this aisle

People compared these

Same shelf, same checkout — eight coins and a 30-minute rate lock.