We take cryptocurrency — so the coins you hold can buy real hardware.Pay in crypto, spend it on real hardware. Free insured shipping worldwide over $399. Plain, unbranded boxes, sent from Germany.Free insured shipping over $399. Your rate is locked for 30 minutes once checkout opens.Rate locked 30 minutes. Every item sealed, serial-checked and covered by a 24-month warranty.Sealed, 24-month warranty.

Saved items Sign in
Green rectangular circuit board with microSD slot and 22-pin SATA connector, 6.0 by 5.0 cm

TeKit

TeKit Micro SD to SATA 22pin Adapter 2.5" Enclosure

SKU CH-P6HX-Y10NF

Converts a Micro SD card into a bootable 2.5" SATA drive for legacy OS support

  • SpecificationsMicro SD TF Card 22pin SATA Adapter Converter Module Board 2
  • FeaturesMicro SD TF Card to 22pin SATA Adapter Card 2.5" HDD Enclosu
  • Dimensions6.0x5.0cm/2.36x1.97in
  • Weight20G
  • Package Contents1 PACK
  • Boot from Micro SD card on any SATA host
  • Replace a 2.5" SATA drive with a TF card
  • SATA 1.0a compliant for broad OS compatibility
  • Hot-plug support lets you swap cards without power down
  • Ultra-low power draw suits embedded and portable builds

Micro SD to SATA 22pin Adapter

This TeKit adapter converts a Micro SD (TF) card into a 2.5 inch SATA drive form factor using a 22pin connector. It presents the card as a standard SATA hard drive to the operating system and supports bootable configurations. The board measures 6.0 by 5.0 centimetres and weighs 20 grams. No drivers are required for operation.

Suitable for legacy SATA slots and bootable TF cards

Builders repairing older laptops, industrial PCs, or embedded systems with a 2.5 inch SATA bay can use this adapter to run an OS from a TF card. It complies with the Serial ATA 1.0a specification and supports hot-plug functionality. Buyers who need UHS-I speeds should look elsewhere, as this adapter does not support that protocol. The package includes only the converter card.

Serial ATA 1.0a compliance decides fit

The adapter follows the Serial ATA 1.0a specification, which determines the maximum transfer rate available through the 22pin SATA interface. If the host system requires a newer SATA revision for full performance, this card will operate at the 1.0a level. Verify that the target device accepts a 2.5 inch SATA drive and can boot from the connected TF card.

Highlights

  • Boot from Micro SD card on any SATA host
  • Replace a 2.5" SATA drive with a TF card
  • SATA 1.0a compliant for broad OS compatibility
  • Hot-plug support lets you swap cards without power down
  • Ultra-low power draw suits embedded and portable builds

Specifications

BrandTekit
SpecificationsMicro SD TF Card 22pin SATA Adapter Converter Module Board 2.5" Hdd Enclosure
FeaturesMicro SD TF Card to 22pin SATA Adapter Card 2.5" HDD Enclosure TF Cards to SATA
Dimensions6.0x5.0cm/2.36x1.97in
Weight20G
Package Contents1 PACK

Questions about this item

Which Micro SD card form factor does the 22pin SATA adapter accept?

The adapter accepts standard Micro SD (TF) cards that fit the on-board slot.

Will the adapter work with a legacy motherboard that only has SATA 1.0a ports?

Yes, the board is Serial ATA 1.0a Specification compliant and supports hot-plug on those ports.

How can I verify the TF card appears as a normal SATA drive after installation?

Open Disk Management in Windows or the equivalent partition tool on Mac or Linux; the card will show as a regular SATA volume ready to format.

New to this? Buying PC parts with Monero — what to check, what it costs to pay, and what is never asked for.

Also in this aisle

People compared these

Same shelf, same checkout — eight coins and a 30-minute rate lock.