We take cryptocurrency — so the coins you hold can buy real hardware.Pay in crypto, spend it on real hardware. Free insured shipping worldwide over $399. Plain, unbranded boxes, sent from Germany.Free insured shipping over $399. Your rate is locked for 30 minutes once checkout opens.Rate locked 30 minutes. Every item sealed, serial-checked and covered by a 24-month warranty.Sealed, 24-month warranty.

Saved items Sign in
Black 60mm square case fan with 4-pin PWM connector

SXDOOL

SXDOOL AFC0612D 60mm 12V 0.60A 4250RPM 23.4CFM 34dBA 4-pin case fan

SKU CH-7PKD-TWXX3 MPN AFC0612D

60 mm dual-ball-bearing PWM fan moves 23.4 CFM at 4250 RPM with 34 dBA noise

  • Fan Size60mm
  • Bearing Type2 Ball
  • RPM4000-4499 RPM
  • Air Flow20-25 CFM
  • Noise Level20 - 25 dBA
  • Power Connector4 Pin
  • 60 mm frame fits tight chassis builds
  • 4-pin PWM connector enables precise motherboard speed control
  • 4 CFM airflow at 4250 RPM clears heat from dense component layouts
  • Dual ball bearing design extends operational lifespan under continuous load
  • 34 dBA noise output keeps acoustic levels low during high-speed operation

Compact 60 mm PWM cooler

The SXDOOL AFC0612D is a 60 mm case fan built for tight spaces that need active airflow. It runs on a 12 V four-pin PWM header so the motherboard can vary speed automatically. The dual ball bearing is rated for long service in continuous operation. Black frame and non-LED blades keep the look neutral inside any chassis.

Upgrade from smaller or sleeve-bearing fans

This unit replaces 40 mm or 50 mm fans that cannot move enough air, or sleeve-bearing models that develop noise over time. The jump is worth it when a component runs hotter than its throttle point and the mounting holes accept a 60 mm frame. PWM control lets the board spin the fan down during idle loads, cutting acoustic impact without losing peak capacity.

Handles focused spot-cooling headroom

At 4 250 RPM the fan delivers 23.4 CFM while measuring 34 dBA, giving enough pressure for VRM heatsinks, chipset blocks or drive cages. Headroom exists for short bursts above the nominal curve, but sustained loads above the rated current will hit the 1.56 W power limit. It is not for builds that need high-volume airflow across large radiators or multiple drive bays.

Highlights

  • 60 mm frame fits tight chassis builds
  • 4-pin PWM connector enables precise motherboard speed control
  • 4 CFM airflow at 4250 RPM clears heat from dense component layouts
  • Dual ball bearing design extends operational lifespan under continuous load
  • 34 dBA noise output keeps acoustic levels low during high-speed operation

Specifications

Fan Size60mm
Bearing Type2 Ball
RPM4000-4499 RPM
Air Flow20-25 CFM
Noise Level20 - 25 dBA
Power Connector4 Pin
ColorBlack
LEDNon-LED

Questions about this item

What mounting holes does the 60mm frame use?

The 60mm square frame follows the standard 60mm mounting pattern with four corner holes spaced for M3 screws.

How do I connect the 4-pin PWM lead to the motherboard?

Align the keyed 4-pin connector with the motherboard CPU or chassis fan header and press straight down until it clicks; the fourth wire carries the PWM control signal.

When should I replace the dual-ball bearing fan?

Replace the fan if bearing noise rises above the rated 34dBA or if RPM drops noticeably below the 4250RPM specification under full PWM duty.

New to this? Which coin should you pay with — what to check, what it costs to pay, and what is never asked for.

Also in this aisle

People compared these

Same shelf, same checkout — eight coins and a 30-minute rate lock.