We take cryptocurrency — so the coins you hold can buy real hardware.Pay in crypto, spend it on real hardware. Free insured shipping worldwide over $399. Plain, unbranded boxes, sent from Germany.Free insured shipping over $399. Your rate is locked for 30 minutes once checkout opens.Rate locked 30 minutes. Every item sealed, serial-checked and covered by a 24-month warranty.Sealed, 24-month warranty.

Saved items Sign in
Two 30 cm SFF-8482 SAS 29-pin to SATA 7-pin female cables with 4-pin Molex power connectors

SMUGDESK

SMUGDESK SFF-8482 SAS 29 Pin to SATA III 7Pin Female-Female Cable with 4Pin LP4 Molex Power, 30cm, Pack of 2

SKU CH-R4MM-R9612

Converts SAS 8482 to SATA 3.0 with integrated LP4 Molex power, 30 cm length, pack of 2

  • Converts SAS 8482 to SATA 3.0 for drive compatibility
  • Integrated 4Pin Molex powers drives without extra cables
  • 30cm length fits tight server and NAS chassis
  • Two cables per pack support multi-channel RAID expansion
  • Shielded wiring maintains stable 6Gbps signal transmission

SAS to SATA adapter cable

This SMUGDESK cable converts an SFF-8482 SAS 29Pin interface to a standard SATA III 7Pin connector for connecting SATA hard drives to SAS controllers. An integrated 4Pin LP4 Molex port supplies drive power through the same assembly. The female-to-female design enables direct interconnection without additional adapters. Each pack contains two cables for multi-drive configurations.

SATA 3.0 signal limit

The cable complies with the SATA 3.0 standard for 6Gbps transmission speed between the host adapter and the attached drive. Signal integrity depends on the 30cm length and shielding quality to reduce interference in dense chassis environments. Actual throughput is constrained by the slowest device in the link, whether the SAS controller or the SATA drive. No protocol conversion beyond physical pin mapping is performed.

30cm length constraint

The fixed 30cm (11.8 inch) length determines whether the cable reaches between your controller port and drive bay in a given chassis. Longer runs require a different cable; shorter runs leave no slack for cable management. Measure the internal routing path before ordering to confirm the 30cm reach suits your server, NAS or surveillance recorder layout.

Highlights

  • Converts SAS 8482 to SATA 3.0 for drive compatibility
  • Integrated 4Pin Molex powers drives without extra cables
  • 30cm length fits tight server and NAS chassis
  • Two cables per pack support multi-channel RAID expansion
  • Shielded wiring maintains stable 6Gbps signal transmission

Specifications

No published specifications for this item yet.

Questions about this item

Which version should I choose for a SAS controller with a 29-pin port?

This cable uses the SFF-8482 standard, converting a 29-pin SAS connector to a SATA 3.0 7-pin female port with an integrated 4-pin LP4 Molex power plug, so it matches controllers and backplanes that expose the 29-pin SAS interface.

What does the SATA 3.0 rating mean when the cable is installed in a server?

The cable supports the SATA III 6 Gbps signalling rate, allowing a SATA hard drive or SSD to run at its native speed when connected to a SAS host adapter or RAID controller through this adapter.

What interface standard does the cable follow and what speed does it cap at?

It complies with the SATA 3.0 specification, which limits the data path to 6 Gbps, while the SAS side uses the SFF-8482 29-pin form factor for compatibility with SAS controllers and backplanes.

New to this? Which coin should you pay with — what to check, what it costs to pay, and what is never asked for.

Also in this aisle

People compared these

Same shelf, same checkout — eight coins and a 30-minute rate lock.