We take cryptocurrency — so the coins you hold can buy real hardware.Pay in crypto, spend it on real hardware. Free insured shipping worldwide over $399. Plain, unbranded boxes, sent from Germany.Free insured shipping over $399. Your rate is locked for 30 minutes once checkout opens.Rate locked 30 minutes. Every item sealed, serial-checked and covered by a 24-month warranty.Sealed, 24-month warranty.

Saved items Sign in
Slimline SAS SFF8654 4i 38pin to four 90degree SATA cable 1m

SMUGDESK

SMUGDESK PCIe 4.0 Slimline SAS SFF8654 4i 38Pin to 4×90° SATA 1m

SKU CH-T5VP-T8XWQ

Connects a PCIe 4.0 Slimline SAS SFF8654 4i port to four 90° SATA drives using 30AWG copper for stable high-speed data transfer

  • PCIe 4.0 Slimline SAS SFF8654 4i connects to four SATA drives
  • 90° right-angle SATA plugs fit tight server enclosures
  • 30AWG pure copper conductors reduce signal loss for stable transfer
  • Female SATA ports allow quick HDD or SSD expansion
  • 1 m / 39.37 in length supports clean internal cable routing

Slimline SAS SFF8654 4i to SATA cable

This SMUGDESK harness converts a PCIe 4.0 Slimline SAS SFF8654 4i 38pin connector into four 90degree female SATA ports. It is designed for administrators expanding storage inside enterprise servers, RAID arrays or multi-drive systems using existing Slimline SAS backplanes or controllers.

30AWG copper with right-angle SATA plugs

The cable uses 30AWG pure copper conductors and anti-interference shielding for stable high-speed data transfer. Each 90degree SATA connector reduces the bend radius behind drives, making daily cable routing practical in dense chassis where straight plugs would block adjacent bays or airflow paths.

Check controller port keying and drive power

Before ordering, verify that your host controller or backplane presents a Slimline SAS SFF8654 4i receptacle rather than a different pin-count or keying. Confirm that target drives accept standard SATA data connectors and that separate power cables are available, as this harness carries data only.

Highlights

  • PCIe 4.0 Slimline SAS SFF8654 4i connects to four SATA drives
  • 90° right-angle SATA plugs fit tight server enclosures
  • 30AWG pure copper conductors reduce signal loss for stable transfer
  • Female SATA ports allow quick HDD or SSD expansion
  • 1 m / 39.37 in length supports clean internal cable routing

Specifications

No published specifications for this item yet.

Questions about this item

What bandwidth does the PCIe 4.0 Slimline SAS SFF8654 4i interface support in practice?

The cable is PCIe 4.0 compliant and converts a single SFF8654 4i 38pin connector into four SATA ports, so each SATA device runs at up to 6 Gb/s while the upstream link carries up to PCIe 4.0 x4 speeds.

What clearance does the 90-degree SATA connector need to fit inside a server chassis?

Each female SATA plug uses a right-angle 90degree design that keeps the cable close to the drive, allowing tight routing in compact enclosures without blocking adjacent bays.

How do I install the harness, and which step do people often miss?

Connect the SFF8654 4i end to the controller or backplane, then plug each 90degree SATA connector into the drive; the step often missed is fully seating the Slimline SAS latch until it clicks, otherwise the link will not train at PCIe 4.0 speeds.

New to this? Which coin should you pay with — what to check, what it costs to pay, and what is never asked for.

Also in this aisle

People compared these

Same shelf, same checkout — eight coins and a 30-minute rate lock.