We take cryptocurrency — so the coins you hold can buy real hardware.Pay in crypto, spend it on real hardware. Free insured shipping worldwide over $399. Plain, unbranded boxes, sent from Germany.Free insured shipping over $399. Your rate is locked for 30 minutes once checkout opens.Rate locked 30 minutes. Every item sealed, serial-checked and covered by a 24-month warranty.Sealed, 24-month warranty.

Saved items Sign in
Sanyo PLC-XP100L-LAMP DLP replacement lamp module with Ushio NSHA330W7878 bulb inside

Sanyo

Sanyo PLC-XP100L-LAMP DLP Replacement Lamp 330W

SKU CH-2B22-BBN7A

A 330 W Ushio lamp module restores brightness to the Sanyo PLC-XP100L projector

  • TypeProject Lamp
  • Weight0.9990
  • Ready-to-install module saves setup time
  • Ushio NSHA330W7878 bulb delivers 330 W brightness
  • Genuine Sanyo PLC-XP100L part ensures exact fit
  • Lightweight 0.9990 kg housing eases ceiling mounts
  • 240 day coverage protects your investment

Replacement lamp for Sanyo PLC-XP100L

This 330 W DLP replacement lamp restores brightness to the Sanyo PLC-XP100L projector. It ships as a complete lamp-and-housing module so installation is straightforward. The unit uses a Ushio NSHA330W7878 bulb and weighs .9990 kg. It is intended for venues and classrooms that rely on this specific projector model.

When to replace the original lamp

The module replaces the factory lamp when its output has faded or the projector signals end-of-life. A swap is worth it when image quality drops below the level required for presentations or screenings. The 240 day warranty period covers early failures after installation. Buyers who need a different projector model or a bare bulb without housing cannot use this part.

Limits of the 330 W lamp interface

The lamp operates at AC 330 W and is keyed to the PLC-XP100L power supply and ignition circuit. It will not strike in projectors that expect a different wattage or connector layout. Brightness and colour stability are bound by the original optical engine design. Users who require higher lumen output or a different colour gamut must change the projector itself.

Highlights

  • Ready-to-install module saves setup time
  • Ushio NSHA330W7878 bulb delivers 330 W brightness
  • Genuine Sanyo PLC-XP100L part ensures exact fit
  • Lightweight 0.9990 kg housing eases ceiling mounts
  • 240 day coverage protects your investment

Specifications

BrandSanyo
ModelPLC-XP100L-LAMP
Part NumberPLC-XP100L-LAMP
TypeProject Lamp
Weight0.9990

Questions about this item

What projector model does the PLC-XP100L-LAMP lamp and housing module fit?

The module is built for the Sanyo PLC-XP100L projector and ships as a complete lamp-and-housing assembly ready to slide into that chassis.

Which steps are required to install the Ushio NSHA330W7878 lamp module, and where do installers most often go wrong?

Power off the projector, let it cool, remove the lamp cover, release the retaining screws, slide the old module out, insert the new one until it seats firmly, re-tighten the screws, replace the cover, then reset the lamp timer in the menu — skipping the timer reset is the step most often missed.

When will the 330 W Ushio bulb inside this housing need replacement, and what part should be ordered?

Replace the module when brightness drops noticeably or the projector signals end of lamp life; order the same PLC-XP100L-LAMP lamp-and-housing unit with the Ushio NSHA330W7878 bulb to restore original output.

Also in this aisle

People compared these

Same shelf, same checkout — eight coins and a 30-minute rate lock.