sakose
sakose MICPH-6 6 ft instrument cable 1/4" stereo to 3-pin XLR male 16AWG 97.5% shielded
A 6 ft balanced cable with 1/4" stereo plug to 3-pin XLR male, 16AWG stranded copper and 97.5% shielding
- ColorBlack
- Length6 ft.
- Connector Number2
- Connector DetailPhone plug MALE to 3 pin XLR MALE
- Specifications16AWG Stranded Copper Wire Conduits. 97.5% Shielded Balanced
- FeaturesPhone plug MALE to 3 pin XLR MALE
- Balanced 3-pin XLR male connector ensures clean signal transfer
- 16AWG stranded copper conductors deliver low-resistance audio path
- 5% shielded construction rejects electromagnetic interference
- 6 ft length suits stage and studio setups
- 1/4" stereo phone plug fits standard instrument outputs
Professional audio interconnect
The sakose MICPH-6 is a 6 ft instrument cable built for stage and studio use. It connects a 1/4 inch stereo phone plug to a 3-pin XLR male, carrying balanced signals between microphones, mixers and interfaces. Musicians and engineers who need a single, ready-to-run link will find the length practical for typical rack-to-floor or stand-to-desk runs.
Balanced line limits
The 16AWG stranded copper conductors and 97.5% shielding keep noise low on balanced connections, but the cable cannot fix ground-loop hum caused by mismatched power circuits. Length is fixed at 6 ft, so longer stage runs or permanent installs will require additional cable or a different length. The stereo phone plug carries two conductors plus ground; it will not carry a mono TS signal without an adapter.
Build and daily handling
Black PVC jacket protects the 16AWG stranded cores and dense braid during repeated coiling. Both connectors are male, so the cable plugs directly into a microphone or DI output and a mixer or interface input without gender changers. The 3-pin XLR latch secures against accidental pulls, while the 1/4 inch plug seats firmly in standard jacks. No strain-relief boots are mentioned, so careful unplugging extends service life.
Highlights
- Balanced 3-pin XLR male connector ensures clean signal transfer
- 16AWG stranded copper conductors deliver low-resistance audio path
- 5% shielded construction rejects electromagnetic interference
- 6 ft length suits stage and studio setups
- 1/4" stereo phone plug fits standard instrument outputs
Specifications
| Brand | BYTECC |
|---|---|
| Model | MICPH-6 |
| Color | Black |
| Length | 6 ft. |
| Connector Number | 2 |
| Connector Detail | Phone plug MALE to 3 pin XLR MALE |
| Specifications | 16AWG Stranded Copper Wire Conduits. 97.5% Shielded Balanced Connections |
| Features | Phone plug MALE to 3 pin XLR MALE |
Questions about this item
Should I choose a different length or connector type for my setup?
This model is a fixed 6 ft cable with a 1/4" stereo phone plug on one end and a 3-pin XLR male on the other; no other lengths or connector variants are offered for the MICPH-6.
What does the 97.5% shielding figure mean when I plug this into a mixer?
The 97.5% shield coverage on the 16AWG stranded copper conductors rejects RF and EMI noise, so balanced signals stay clean over the full 6 ft run in stage or studio environments.
Does the 1/4" stereo plug carry a balanced signal into the XLR?
Yes, the 1/4" TRS phone plug is wired for balanced connection through the 16AWG conductors to the 3-pin XLR male, maintaining the 97.5% shielded path end to end.
New to this? Which coin should you pay with — what to check, what it costs to pay, and what is never asked for.
Also in this aisle
People compared these
Same shelf, same checkout — eight coins and a 30-minute rate lock.
Black Box Corporation
Black Box Corporation CAT6 EZ-RJ45 Modular Plugs 100-Pack
$95.99
0.00115713BTC
In stock
