We take cryptocurrency — so the coins you hold can buy real hardware.Pay in crypto, spend it on real hardware. Free insured shipping worldwide over $399. Plain, unbranded boxes, sent from Germany.Free insured shipping over $399. Your rate is locked for 30 minutes once checkout opens.Rate locked 30 minutes. Every item sealed, serial-checked and covered by a 24-month warranty.Sealed, 24-month warranty.

Saved items Sign in
Small green circuit board with gold HDMI port and multiple pin headers

Ruth's sister

Ruth's sister EDP 30pin Driver Board for LP116WH7 SPB1 1920*1080

SKU CH-0EKM-HYRA8

EDP 30-pin driver board with HDMI 1.4 input and 5 V–20 V power for 1920×1080 panels

  • EDP 30-pin driver board fits 10 to 13 inch LCD panels
  • HDMI 1.4 input supports 1920×1080 and lower resolutions
  • Wide 5 V to 20 V power range suits varied setups
  • Gold-plated HDMI port and high-temp components for durable operation
  • Jump-cap adjustment matches 1920×1200, 1600×900, 1366×768, 1280×800 screens

Target display and input

This EDP 30-pin driver board is built for the LP116WH7 SPB1 panel and accepts a single HDMI 1.4 signal. It supports resolutions up to 1920 x 1200 and works with common 10 to 13 inch screens such as 1920 x 1080, 1600 x 900 and 1366 x 768. Makers integrating a tablet LCD into a custom project will find the standard HDMI connector and wide voltage range straightforward to wire.

Thermals and power in normal use

The board operates from a 5 V to 20 V supply and uses high-temperature components rated for extended operation in warm environments. A standard 6-pin backlight connector and EDP-30-pin output keep cabling simple. Adequate ventilation is recommended so the components stay within their thermal limits during typical desktop or embedded workloads.

Behaviour under sustained load

Jumper-cap adjustment matches the driver to the exact panel resolution before long-term deployment. The design includes HDMI and 4-pin IIC upgrade paths for firmware updates without removing the board. Remote control and multi-screen parameter selection remain functional during continuous operation, while the gold-plated HDMI port resists oxidation over months of daily use.

Highlights

  • EDP 30-pin driver board fits 10 to 13 inch LCD panels
  • HDMI 1.4 input supports 1920×1080 and lower resolutions
  • Wide 5 V to 20 V power range suits varied setups
  • Gold-plated HDMI port and high-temp components for durable operation
  • Jump-cap adjustment matches 1920×1200, 1600×900, 1366×768, 1280×800 screens

Specifications

No published specifications for this item yet.

Questions about this item

How do I install the EDP 30-pin driver board and set the jump cap for a 1920*1080 panel?

Connect the HDMI input and 5 V–20 V power, plug the 30-pin EDP cable into the LP116WH7 SPB1 screen, attach the 6-pin backlight connector, then move the jump cap to the position marked for 1920*1080 resolution before powering on.

What maintenance or replacement will the driver board need over time?

The board uses high-temperature components for long life; keep ventilation clear and check the 6-pin backlight cable and HDMI port for dust or loose contacts during routine system cleaning.

What is the first limit reached under sustained heavy use?

The HDMI 1.4 input caps the signal at 1920*1200 maximum resolution, so sustained 4 K or higher refresh rates cannot be passed through this driver board.

New to this? Which coin should you pay with — what to check, what it costs to pay, and what is never asked for.

Also in this aisle

People compared these

Same shelf, same checkout — eight coins and a 30-minute rate lock.