We take cryptocurrency — so the coins you hold can buy real hardware.Pay in crypto, spend it on real hardware. Free insured shipping worldwide over $399. Plain, unbranded boxes, sent from Germany.Free insured shipping over $399. Your rate is locked for 30 minutes once checkout opens.Rate locked 30 minutes. Every item sealed, serial-checked and covered by a 24-month warranty.Sealed, 24-month warranty.

Saved items Sign in
Black 22 cm power splitter cable with single 6-pin and dual 6+2-pin connectors

Ruth's sister

Ruth's sister 6-pin to Dual 6+2-pin Power Splitter Cable 22cm

SKU CH-X6TS-YC878

Splits a single PCIe 6-pin connector into two 6+2-pin plugs using 18 AWG tinned-copper wire, 22 cm long

  • Splits one 6-pin PSU connector into two 6+2-pin GPU plugs
  • 22 cm length keeps cable routing tidy inside the case
  • 18 AWG tinned-copper conductors rated for 80 °C operation
  • Magic 6+2 design works as either 6-pin or 8-pin power input
  • Weighs only 28 g so it adds minimal mass to the build

PCI-E 6-pin to Dual 6+2-pin Splitter

This 22 cm internal power cable splits a single PCI-E 6-pin connector into two 6+2-pin plugs. It suits builders whose power supply lacks enough native PCI-E leads for a graphics card requiring dual connectors. The magic 6+2 design allows each output to serve as either a 6-pin or 8-pin plug. It also functions as a short extension for tight routing.

18 AWG tinned copper conductors

The cable uses UL1007 18 AWG wire built from 34 strands of 0.12 mm tinned copper. PVC insulation provides an outer diameter of 2.1 mm and a rated temperature of 80 °C. Connectors are a 5559 6-pin plug on the supply side and two 5557 6+2 slide-rail sockets on the component side. Total weight is 28 g.

Rated for 80 °C continuous operation

Under normal loads the PVC-insulated 18 AWG conductors run within their 80 °C temperature rating. The short 22 cm length keeps voltage drop and resistive heating low. No active cooling is required and the cable adds negligible acoustic noise to the system.

Highlights

  • Splits one 6-pin PSU connector into two 6+2-pin GPU plugs
  • 22 cm length keeps cable routing tidy inside the case
  • 18 AWG tinned-copper conductors rated for 80 °C operation
  • Magic 6+2 design works as either 6-pin or 8-pin power input
  • Weighs only 28 g so it adds minimal mass to the build

Specifications

No published specifications for this item yet.

Questions about this item

How much current can the 18 AWG wires carry once the splitter is installed in a live system?

The 18 AWG tinned-copper conductors are rated for 80 °C operation and use 34 strands of 0.12 mm wire, a gauge commonly used for PCIe power delivery up to the connector limits.

What does the 5559 6-pin to 5557 6+2-pin interface actually limit in a real build?

The Molex 5559 6-pin plugs into the PSU while each 5557 6+2 slide-rail connector can serve either a 6-pin or 8-pin GPU socket, so the splitter is capped by the single 6-pin source and the 18 AWG wire rating.

Will the 22 cm length and 2.1 mm cable diameter fit behind a typical graphics card in a mid-tower case?

At 22 cm long with a 2.1 mm outer diameter and flexible PVC insulation, the cable routes easily behind most GPUs and adds only 28 g of weight to the harness.

New to this? Which coin should you pay with — what to check, what it costs to pay, and what is never asked for.

Also in this aisle

People compared these

Same shelf, same checkout — eight coins and a 30-minute rate lock.