We take cryptocurrency — so the coins you hold can buy real hardware.Pay in crypto, spend it on real hardware. Free insured shipping worldwide over $399. Plain, unbranded boxes, sent from Germany.Free insured shipping over $399. Your rate is locked for 30 minutes once checkout opens.Rate locked 30 minutes. Every item sealed, serial-checked and covered by a 24-month warranty.Sealed, 24-month warranty.

Saved items Sign in
Short RJ48 to BNC adaptor cable, 18.5 cm, black connectors on grey cable

Roby Technology Co., Limited

Roby Technology Co., Limited RJ48 to BNC Cable 18.5 cm

SKU CH-JXMG-S7T47

An 18.5 cm RJ48 to BNC adaptor cable connects ISDN PRI T1/E1 cards such as TE110P, TE220, TE420, TE430, TE405P, TE407P, TE110E, TE120E.

  • TypeCable
  • SpecificationsBNC RJ48
  • FeaturesBNC RJ48
  • Ready for ISDN PRI T1/E1 cards including TE110P, TE220, TE420
  • Driver-free operation simplifies installation and maintenance
  • No hot-swap support ensures stable, fixed connections
  • 5 cm copper cable meets TIA/EIA and ISO standards
  • Single unit supplied for immediate deployment

RJ48 to BNC Cable 18.5 cm

This new cable converts an RJ48 interface to a BNC connector for ISDN PRI T1 or E1 digital telephone cards. It measures approximately 18.5 cm and uses copper wire built to TIA/EIA and ISO standards. No driver installation is required and the unit does not support hot swapping. The package includes a single cable.

Suits T1/E1 card installers not for hot-swap needs

Installers connecting cards such as TE110P, TE220, TE420, TE430, TE405P, TE407P, TE110E, TE120E, TE410P or TE412P will find this cable matches the required interface. It is not intended for setups that require hot-swappable connections or a different connector type.

Interface RJ48 to BNC decides fit

The sole specification that determines compatibility is the RJ48 to BNC interface conversion. If the target card uses this exact interface pairing the cable will work; if the card requires a different connector arrangement another solution is needed.

Highlights

  • Ready for ISDN PRI T1/E1 cards including TE110P, TE220, TE420
  • Driver-free operation simplifies installation and maintenance
  • No hot-swap support ensures stable, fixed connections
  • 5 cm copper cable meets TIA/EIA and ISO standards
  • Single unit supplied for immediate deployment

Specifications

BrandAsteriskStore
ModelISDN E1 Cable
Part NumberBNC RJ48 Cable
TypeCable
SpecificationsBNC RJ48
FeaturesBNC RJ48

Questions about this item

What card slot do I need on my T1/E1 board for the RJ48 plug to fit?

The cable terminates in an RJ48 connector that matches the RJ48 port on cards such as the TE110P, TE220, TE420, TE430, TE405P, TE407P, TE110E, TE120E, TE410P and TE412P.

Will the 18.5 cm length reach from a rear-panel BNC jack to an adjacent card in a 2 U chassis?

At 18.5 cm the cable is designed for short runs between a BNC bulkhead and a nearby T1/E1 card; measure your specific chassis to confirm the reach before ordering.

How can I verify the link is active after connecting the BNC side to the network termination?

Check the T1/E1 card status LEDs or driver logs for carrier detect and frame sync; the cable itself has no indicators and requires no driver.

Also in this aisle

People compared these

Same shelf, same checkout — eight coins and a 30-minute rate lock.