We take cryptocurrency — so the coins you hold can buy real hardware.Pay in crypto, spend it on real hardware. Free insured shipping worldwide over $399. Plain, unbranded boxes, sent from Germany.Free insured shipping over $399. Your rate is locked for 30 minutes once checkout opens.Rate locked 30 minutes. Every item sealed, serial-checked and covered by a 24-month warranty.Sealed, 24-month warranty.

Saved items Sign in
Four small spools of dual-colour PLA filament in matte and silk finishes

RepRapper Dual Color PLA Filament 1.75mm 4×250g Pack

SKU CH-RCT6-6P5C8

Four spools of 250 g dual-colour PLA filament in matte and silk finishes for 1.75 mm FDM printers

  • ColorDual Color Blue Pla
  • MaterialPolylactic Acid
  • Diameter1.75
  • Weight1 kilograms
  • Four spools give 1 kg of dual-color PLA for varied projects
  • Two colors coextruded along each spool create striking prints without swapping filament
  • Matte and silk finishes in one pack suit both subtle and glossy aesthetics
  • 75 mm diameter works with most FDM printers at 180–220 °C nozzle temps
  • Rigorous CCD checks ensure consistent diameter and reliable layer adhesion

Four spools in one pack

This RepRapper pack contains four 250 g spools of 1.75 mm dual-colour PLA filament. The set includes matte red/blue, matte purple/green, silk red/blue and silk purple/green. It suits makers who want a variety of co-extruded colours without buying full-size reels. The total weight is 1 kg and the material is polylactic acid.

Replaces single-colour reels

Instead of purchasing separate single-colour spools, this pack gives four distinct dual-colour combinations in smaller quantities. The jump is worth it when you need colour transitions on small models, 3D pen work or test prints and do not want leftover filament sitting unused. Each spool provides two colours along its entire length.

Consistent flow on long prints

The filament is produced with dual extrusion and held to tight dimensional accuracy. Recommended nozzle temperature is 180 to 220 °C, bed temperature 40 to 60 °C and print speed 40 to 100 mm/s. Drying at 50 to 60 °C for 6 to 8 hours before each session helps maintain steady extrusion during extended builds.

Highlights

  • Four spools give 1 kg of dual-color PLA for varied projects
  • Two colors coextruded along each spool create striking prints without swapping filament
  • Matte and silk finishes in one pack suit both subtle and glossy aesthetics
  • 75 mm diameter works with most FDM printers at 180–220 °C nozzle temps
  • Rigorous CCD checks ensure consistent diameter and reliable layer adhesion

Specifications

BrandRepRapper
ModelREP-DUALPLA-1.75MM-4x250G-PACK-A
ColorDual Color Blue Pla
MaterialPolylactic Acid
Diameter1.75
Weight1 kilograms

Questions about this item

What spool size and filament diameter does my printer need to accept for these four 250 g packs?

Each spool weighs 250 g and the filament diameter is 1.75 mm, so the printer must support 1.75 mm filament and a standard spool hub.

Which temperature settings and drying step are recommended before the first print?

Heat the nozzle to 180–220 °C, the bed to 40–60 °C, print at 40–100 mm/s, and dry the filament at 50–60 °C for 6–8 hours before printing.

How should I store the spools between prints to keep them printable?

Keep each spool in a sealed bag with desiccant; if the filament absorbs moisture, dry it again at 50–60 °C for 6–8 hours before the next use.

Also in this aisle

People compared these

Same shelf, same checkout — eight coins and a 30-minute rate lock.