We take cryptocurrency — so the coins you hold can buy real hardware.Pay in crypto, spend it on real hardware. Free insured shipping worldwide over $399. Plain, unbranded boxes, sent from Germany.Free insured shipping over $399. Your rate is locked for 30 minutes once checkout opens.Rate locked 30 minutes. Every item sealed, serial-checked and covered by a 24-month warranty.Sealed, 24-month warranty.

Saved items Sign in
Two dark gray epoxy paste tubes in a small box

PROTECTIVE COATING CO

PROTECTIVE COATING CO PC-7 2 OZ Dark Gray 2 Component Epoxy Paste

SKU CH-ZE6Q-MMNH2

Two-part epoxy paste bonds, seals and fills fiberglass, wood, concrete, metals, brick, glass, ceramic and rubber for indoor and outdoor repairs

  • TypeGlue
  • Selling UnitEach
  • Quantity1 each
  • Heavy-duty epoxy bonds fiberglass, wood, concrete, metals, brick, glass, ceramic and rubber
  • Non-sagging high-tack paste works on vertical and overhead surfaces without running
  • 60-minute working time at 70 degrees F gives ample positioning flexibility
  • Cured adhesive resists mild acids, caustics, gasoline, fuel oil, fresh and salt water
  • Paintable, stainable, machinable, nontoxic and nonconductive after full cure

Two-Part Epoxy Paste for Repairs

The PC-7 epoxy paste is a two-component adhesive that bonds, seals and fills in a single product. It suits DIYers, maintenance crews and trade professionals who need one material for fiberglass, wood, concrete, metals, brick, glass, ceramic and rubber. The dark-grey paste comes in a 2 oz pack ready for indoor or outdoor jobs. It is non-toxic and non-conductive once fully cured.

Temperature Range and Working Time

Application is possible between 35 and 115 degrees F, and the cured joint withstands service temperatures from -20 to +200 degrees F. At 70 degrees F the mixture remains workable for up to 60 minutes before it begins to set. Full cure for service occurs overnight, with exact timing dependent on temperature, humidity and the size of the application.

Post-Cure Versatility

After maximum cure the epoxy can be painted, stained or machined to match surrounding surfaces. It resists mild acids, caustics, detergents, gasoline, fuel oil and both fresh and salt water. These properties let the same material seal tank leaks, repair plumbing and masonry cracks, and fill holes, castings or moulds without needing separate products.

Highlights

  • Heavy-duty epoxy bonds fiberglass, wood, concrete, metals, brick, glass, ceramic and rubber
  • Non-sagging high-tack paste works on vertical and overhead surfaces without running
  • 60-minute working time at 70 degrees F gives ample positioning flexibility
  • Cured adhesive resists mild acids, caustics, gasoline, fuel oil, fresh and salt water
  • Paintable, stainable, machinable, nontoxic and nonconductive after full cure

Specifications

TypeGlue
Selling UnitEach
Quantity1 each

Questions about this item

How do I mix and apply the two-part PC-7 epoxy paste, and what is the common mistake?

Mix equal parts of resin and hardener until the dark grey colour is uniform, then apply within 60 minutes at 70 °F. The frequent error is stopping the mix too early, leaving streaks that never cure.

Will the cured epoxy need any maintenance or replacement over time?

Once fully cured, the bond resists mild acids, caustics, detergents, gasoline, fuel oil and fresh or salt water from -20 °F to 200 °F. It can be painted, stained or machined, and no scheduled replacement is required.

What is the first limitation I will hit during continuous heavy-duty use?

The service temperature ceiling of 200 °F is the first hard limit; above that the epoxy can soften and lose structural strength even though it resists chemicals and water.

Also in this aisle

People compared these

Same shelf, same checkout — eight coins and a 30-minute rate lock.