We take cryptocurrency — so the coins you hold can buy real hardware.Pay in crypto, spend it on real hardware. Free insured shipping worldwide over $399. Plain, unbranded boxes, sent from Germany.Free insured shipping over $399. Your rate is locked for 30 minutes once checkout opens.Rate locked 30 minutes. Every item sealed, serial-checked and covered by a 24-month warranty.Sealed, 24-month warranty.

Saved items Sign in
Green PLA filament spool in vacuum-sealed packaging

PrintOxe

PrintOxe Apple Green PLA Filament 1.75mm 1Kg

SKU CH-A7SK-7WX39

Apple Green PLA filament on a 1 kg spool with 1.75 mm diameter and ±.03 mm accuracy for reliable 3D printing

  • ColorApple Green
  • MaterialPLA
  • Diameter1.75 mm
  • Melting Point180°C - 210°C (356°F - 410°F)
  • Weight1Kg. (2.2 LB)
  • Consistent extrusion with ±0.03 mm dimensional accuracy
  • Ready-to-print filament vacuum-sealed with desiccant against moisture
  • Broad printer compatibility across MakerBot, RepRap, Flashforge and more
  • Reliable flow at 180°C–210°C nozzle temperature range
  • Standard 1.75 mm diameter fits common extruder setups

Filament type and target use

PrintOxe Apple Green PLA filament comes on a 1.75 mm spool with a net weight of 1 kilogram. The material is polylactic acid formulated for general-purpose 3D printing. Dimensional accuracy is held to ± .03 mm. It suits hobbyists and makers who need a reliable, easy-to-print filament for everyday models and prototypes.

Thermal behaviour and power considerations

The recommended extrusion temperature range is 180 °C to 210 °C (356 °F to 410 °F). PLA melts at lower temperatures than many other polymers, so the hot-end draws modest power during printing. No heated bed is required, which further reduces overall energy use and keeps the printer quieter during long jobs.

Packaging benefits and practical impact

Each spool is vacuum-sealed with desiccant inside the retail box to protect the filament from humidity and moisture. The spool dimensions are 7.80 inch diameter, 2.56 inch width and a 2.20 inch hub hole (19.50 cm, 6.50 cm, 5.59 cm). This packaging keeps the material dry and ready to print without additional drying steps.

Highlights

  • Consistent extrusion with ±0.03 mm dimensional accuracy
  • Ready-to-print filament vacuum-sealed with desiccant against moisture
  • Broad printer compatibility across MakerBot, RepRap, Flashforge and more
  • Reliable flow at 180°C–210°C nozzle temperature range
  • Standard 1.75 mm diameter fits common extruder setups

Specifications

BrandPrintOxe
ColorApple Green
MaterialPLA
Diameter1.75 mm
Melting Point180°C - 210°C (356°F - 410°F)
Weight1Kg. (2.2 LB)

Questions about this item

How do I load the 1.75 mm PrintOxe PLA spool onto my printer, and what step often causes jams?

Mount the spool on a holder matching the 5.59 cm hub hole, feed the filament straight into the extruder, and avoid sharp bends near the 19.50 cm outer flange — that bend is the most common cause of first-layer jams.

What upkeep will this Apple Green PLA need after months of printing?

Keep the vacuum-sealed bag and desiccant; reseal the 1 kg spool after each use to stop moisture absorption, and wipe the 1.75 mm filament with a lint-free cloth if dust collects during long idle periods.

At what point does sustained printing hit a thermal limit with this filament?

The recommended nozzle range tops out at 210 °C; pushing above that during long prints risks heat creep and degraded layer adhesion, so treat 210 °C as the practical ceiling for continuous extrusion.

Also in this aisle

People compared these

Same shelf, same checkout — eight coins and a 30-minute rate lock.