We take cryptocurrency — so the coins you hold can buy real hardware.Pay in crypto, spend it on real hardware. Free insured shipping worldwide over $399. Plain, unbranded boxes, sent from Germany.Free insured shipping over $399. Your rate is locked for 30 minutes once checkout opens.Rate locked 30 minutes. Every item sealed, serial-checked and covered by a 24-month warranty.Sealed, 24-month warranty.

Saved items Sign in
Black 10-inch car subwoofer with silver cone and rubber surround

Pioneer

Pioneer TS-D10D2 10" Dual 2-Ohm Car Subwoofer

SKU CH-00G2-87WZ0

A 10-inch car subwoofer with dual 2-ohm voice coils, 500W RMS power and an Aramid Fiber IMPP cone for deep, accurate bass

  • Feature10" Subwoofer
  • Deep bass impact from 500W RMS / 1500W max power
  • Flexible wiring options with dual 2-ohm voice coils
  • Strong, lightweight cone using 10" Aramid Fiber IMPP material
  • Accurate cone control via butyl rubber surround
  • Fits tight spaces with 5.5" mounting depth

Compact 10-inch subwoofer for car audio enthusiasts

The Pioneer TS-D10D2 is a 10-inch car subwoofer built for listeners who want deep, punchy bass from a single driver. Its dual 2-ohm voice coils give installers wiring flexibility for mono or stereo amplifier configurations. The Aramid Fiber IMPP cone and butyl rubber surround are designed to handle high excursion while maintaining cone integrity. This driver suits sealed or vented enclosures in daily-driver vehicles.

500 W RMS power handling with 1500 W peak headroom

The subwoofer handles 500 W RMS continuously and peaks at 1500 W, providing ample headroom for dynamic bass passages without thermal compression. Sensitivity sits at 74 dB at 1 W/1 m, so moderate amplifier power produces usable output. Frequency response spans 20 Hz to 6.6 kHz, covering the lowest octaves and blending into mid-bass. Linear excursion of 9.8 mm and a free-air resonance of 40 Hz set the practical low-frequency limit in small enclosures.

Stamped metal basket with 5.5-inch mounting depth

A stamped metal basket keeps the motor structure rigid while fitting a shallow 5.5-inch mounting depth, easing installation behind tight factory panels. The 9-inch cutout diameter matches common 10-inch openings. Dual 2-ohm coils allow 1-ohm or 4-ohm final loads, letting the installer match the amplifier's stable impedance range. Recommended sealed volume is 0.7 cu ft and vented volume is 0.8 cu ft for optimal alignment.

Highlights

  • Deep bass impact from 500W RMS / 1500W max power
  • Flexible wiring options with dual 2-ohm voice coils
  • Strong, lightweight cone using 10" Aramid Fiber IMPP material
  • Accurate cone control via butyl rubber surround
  • Fits tight spaces with 5.5" mounting depth

Specifications

BrandPioneer
Feature10" Subwoofer

Questions about this item

Will the dual 2-ohm coils let me wire this subwoofer to my existing 1-ohm stable amplifier?

Yes. The dual 2-ohm voice coils can be wired in parallel for a 1-ohm load, in series for a 4-ohm load, or used independently for a 2-ohm load, giving you three wiring options to match your amplifier's stable impedance.

How can I verify the subwoofer is performing correctly once installed?

Measure the free-air resonance near 40 Hz and confirm the in-box response reaches the rated 20 Hz lower limit. With 500 W RMS applied, listen for clean output without mechanical noise, and check that cone excursion stays within the 9.8 mm Xmax limit.

What comes in the box and what must I supply separately?

The box contains the TS-D10D2 subwoofer only. You must provide an enclosure built to either 0.7 cu. ft. sealed or 0.8 cu. ft. vented volume, a 9-inch cutout, 5.5-inch mounting depth, amplifier, wiring, and any grille or trim you prefer.

Also in this aisle

People compared these

Same shelf, same checkout — eight coins and a 30-minute rate lock.