We take cryptocurrency — so the coins you hold can buy real hardware.Pay in crypto, spend it on real hardware. Free insured shipping worldwide over $399. Plain, unbranded boxes, sent from Germany.Free insured shipping over $399. Your rate is locked for 30 minutes once checkout opens.Rate locked 30 minutes. Every item sealed, serial-checked and covered by a 24-month warranty.Sealed, 24-month warranty.

Saved items Sign in
White rectangular probe unit with BNC cable and hook accessories

Pintech

Pintech N1140Apro 50MHz 14kV 1000X/100X differential probe measurement tool

SKU CH-HZAS-VQ3MH MPN N1140Apro

High-voltage differential probe measures up to 14 kV with 50 MHz bandwidth, selectable 100X or 1000X attenuation and ±0.5 % accuracy

  • Size/Dimensions187*83*41mm
  • Selling UnitEach
  • TypeElectrical Testing & Measuring
  • Accuracy±0.5%(DC-50Hz~1KHz)
  • Standards/CertificationsCE
  • Measures up to 14 kV peak-to-peak for high-voltage circuits
  • 50 MHz bandwidth captures fast transients accurately
  • ±0.5 % accuracy after brief warm-up ensures reliable readings
  • Switchable 100X and 1000X attenuation ratios suit varied signals
  • BNC connector fits any oscilloscope with 1 MΩ input

High-voltage differential probe for oscilloscopes

The Pintech N1140Apro is a 50 MHz bandwidth differential probe rated for 14 kV peak-to-peak measurement. It converts floating two-point signals to ground-referenced outputs for oscilloscopes and data acquisition systems. Selectable 100X and 1000X attenuation ratios suit motor-drive and power-electronics testing.

Sustained-load behaviour and accuracy

Accuracy is specified at ±0.5 % from DC through 50 Hz to 1 kHz after a one-to-two-minute warm-up. The 7 ns rise time and 36 MΩ // 1 pF differential input impedance maintain signal fidelity during extended captures. Common-mode rejection exceeds 80 dB at 60 Hz and 50 dB at 100 kHz, limiting error from ground offsets during long sessions.

BNC interface and power constraints

The probe terminates in a BNC connector on a 90 cm cable for direct connection to a 1 MΩ oscilloscope input. A 6 V DC 300 mA mains adaptor powers the active circuitry, so a suitable outlet is required. Input leads are 30 cm long, and the unit weighs 425 g in a 187 × 83 × 41 mm housing.

Highlights

  • Measures up to 14 kV peak-to-peak for high-voltage circuits
  • 50 MHz bandwidth captures fast transients accurately
  • ±0.5 % accuracy after brief warm-up ensures reliable readings
  • Switchable 100X and 1000X attenuation ratios suit varied signals
  • BNC connector fits any oscilloscope with 1 MΩ input

Specifications

BrandPINTECH
ModelN1140Apro
Size/Dimensions187*83*41mm
Selling UnitEach
TypeElectrical Testing & Measuring
Accuracy±0.5%(DC-50Hz~1KHz)
Standards/CertificationsCE

Questions about this item

How much power does the N1140Apro draw from its 6V DC mains adaptor during all-day use?

The probe is supplied with a 6V DC, 300mA mains adaptor, so continuous operation draws a modest 1.8W from the wall outlet.

Which oscilloscope input impedance must the buyer already have for the probe to meet its ±0.5% accuracy spec?

The probe is calibrated for a 1M oscilloscope input; using a 50 ohm input would alter the attenuation ratio and degrade the stated accuracy.

Can the 90cm BNC cable reach the front panel of a typical bench oscilloscope without an extension?

At 90cm the cable reaches most bench scopes directly; if the instrument sits further back, a standard BNC extension can be added without affecting the 50MHz bandwidth.

Also in this aisle

People compared these

Same shelf, same checkout — eight coins and a 30-minute rate lock.