We take cryptocurrency — so the coins you hold can buy real hardware.Pay in crypto, spend it on real hardware. Free insured shipping worldwide over $399. Plain, unbranded boxes, sent from Germany.Free insured shipping over $399. Your rate is locked for 30 minutes once checkout opens.Rate locked 30 minutes. Every item sealed, serial-checked and covered by a 24-month warranty.Sealed, 24-month warranty.

Saved items Sign in
Yellow nylon fully-insulated crimp socket disconnects, pack of 500

Panduit

Panduit DNF10-250FIB-D wire cap connector 10-12 AWG 600 V

SKU CH-GMEV-VJ6CA

Quick-disconnect crimp terminal for 10-12 AWG wires rated to 600 V with yellow nylon insulation and tin-plated brass contacts

  • TypeElectrical Connectors
  • Crimp-terminated brass socket accepts 10-12 AWG wire up to 600 V
  • Full nylon insulation rated UL 94 HB withstands 221 °F operating temperature
  • Yellow colour coding identifies 0.25 in tab width for quick-disconnect mating
  • Pack of 500 meets CSA 22.2 No. 153 and UL 310 standards
  • RoHS-compliant butted seam construction ensures reliable electrical contact

Quick-disconnect wire caps for 10-12 AWG

These Panduit DNF10-250FIB-D connectors accept 10 to 12 AWG wires rated up to 600 V. The brass contacts carry a tin finish and use a butted seam crimp style. Yellow nylon insulation provides full coverage and meets a UL 94 HB flammability rating. They are supplied in a pack of 500 pieces.

Replaces open-barrel or loose bullet terminals

The quick-disconnect socket fits a standard 0.25 in tab with 0.032 in thickness for a secure mating connection. Upgrade from taped splices when vibration resistance and repeatable disconnection are required. The CSA 22.2 No. 153 and UL 310 listings support compliance in fixed wiring installations. Not suited for wire gauges outside the 10-12 AWG range or for voltages exceeding 600 V.

Crimp installation with standard hand tools

Strip the conductor to the correct length and crimp the butted seam barrel using a calibrated tool for 10-12 AWG. Full nylon coverage reduces the chance of exposed conductor after termination. Verify the tab width and thickness match the 0.25 in by 0.032 in specification before mating. Incorrect crimp force or wrong wire size are the most common causes of failure.

Highlights

  • Crimp-terminated brass socket accepts 10-12 AWG wire up to 600 V
  • Full nylon insulation rated UL 94 HB withstands 221 °F operating temperature
  • Yellow colour coding identifies 0.25 in tab width for quick-disconnect mating
  • Pack of 500 meets CSA 22.2 No. 153 and UL 310 standards
  • RoHS-compliant butted seam construction ensures reliable electrical contact

Specifications

BrandPANDUIT
TypeElectrical Connectors

Questions about this item

Will the .25 in tab width and .032 in tab thickness fit my existing male terminals?

The connector accepts tabs measuring .25 in wide by .032 in thick, matching standard .250 series disconnects. Crimp 10-12 AWG wire into the brass socket using a ratchet crimper for a secure joint.

What crimp tool and technique give a reliable termination on 10-12 AWG wire?

Use a ratchet crimp tool sized for 10-12 AWG butted-seam terminals. Insert stripped wire fully, cycle the tool completely, then tug-test; the nylon insulation and tin-plated brass contact meet UL 310 and CSA 22.2 No. 153.

How often should I inspect or replace these connectors in a high-vibration automotive harness?

Inspect at each major service interval for cracked nylon, discoloured tin plating, or loose crimps. Replace any connector showing heat damage above 221 °F or vibration-induced terminal fretting.

Also in this aisle

People compared these

Same shelf, same checkout — eight coins and a 30-minute rate lock.