We take cryptocurrency — so the coins you hold can buy real hardware.Pay in crypto, spend it on real hardware. Free insured shipping worldwide over $399. Plain, unbranded boxes, sent from Germany.Free insured shipping over $399. Your rate is locked for 30 minutes once checkout opens.Rate locked 30 minutes. Every item sealed, serial-checked and covered by a 24-month warranty.Sealed, 24-month warranty.

Saved items Sign in
Copper reducer trap, 2-1/2 by 2 inch, wrot finish

Nibco, Inc.

Nibco, Inc. 6002 2-1/2x2 Wrot Copper Reducer Trap

SKU CH-VBZ7-AP8RR MPN 6002

A wrot copper reducer fitting connecting 2-1/2 in and 2 in tube sizes with FTG x C ends, rated to 336 psi at 100 Degrees F and a temperature range of -20 to 400 Degrees F per ASME/ANSI B 16.22

  • TypeDrain Components
  • MaterialHAWA
  • Wrot copper construction resists corrosion for long service life
  • Reduces 2-1/2 in. tube to 2 in. for system compatibility
  • Rated to 336 psi at 100 degrees F for high-pressure lines
  • Operates from -20 to 400 degrees F across temperature extremes
  • Meets ASME/ANSI B 16.22 standard for code compliance

Wrot Copper Reducer Trap for Plumbing Systems

This Nibco 6002 reducer connects 2-1/2 inch tube to 2 inch copper pipe using a wrot copper fitting with FTG by C ends. It handles pressures up to 336 psi at 100 degrees Fahrenheit and operates from -20 to 400 degrees Fahrenheit. The component meets ASME/ANSI B 16.22 standards for drain installations.

Suited for Copper Drain Lines Needing Size

Installers reducing drain lines from 2-1/2 to 2 inches in copper systems will find this fitting matches the required dimensions and pressure rating. It is not intended for systems using different tube materials, alternate connection types, or pressure ratings beyond the listed 336 psi limit.

The 336 psi Pressure Rating at 100 Degrees F

This single specification determines whether the reducer matches the design pressure of the drain system. Verify the operating pressure against the 336 psi maximum before selecting this part for the installation.

Highlights

  • Wrot copper construction resists corrosion for long service life
  • Reduces 2-1/2 in. tube to 2 in. for system compatibility
  • Rated to 336 psi at 100 degrees F for high-pressure lines
  • Operates from -20 to 400 degrees F across temperature extremes
  • Meets ASME/ANSI B 16.22 standard for code compliance

Specifications

TypeDrain Components
MaterialHAWA
BrandNibco
Model6002 21/2x2

Questions about this item

What pressure does the ASME/ANSI B 16.22 copper reducer handle in practice?

The fitting is rated for 336 psi at 100 degrees Fahrenheit, which is the maximum working pressure defined by the ASME/ANSI B 16.22 standard for this wrot copper size.

What tube diameters must match for the 2-1/2 by 2 inch fitting to seat correctly?

The outside diameters are 2-5/8 inch on the larger end and 2-1/8 inch on the smaller end; both tubes must match these dimensions for a proper solder joint.

How is the FTG x C reducer installed and which step is often missed?

Clean both tube ends and the fitting sockets, apply flux, insert the tube fully into the cup and the fitting end into the street, then heat evenly; the step often missed is heating the fitting body enough to draw solder into the full depth of both joints.

Also in this aisle

People compared these

Same shelf, same checkout — eight coins and a 30-minute rate lock.