We take cryptocurrency — so the coins you hold can buy real hardware.Pay in crypto, spend it on real hardware. Free insured shipping worldwide over $399. Plain, unbranded boxes, sent from Germany.Free insured shipping over $399. Your rate is locked for 30 minutes once checkout opens.Rate locked 30 minutes. Every item sealed, serial-checked and covered by a 24-month warranty.Sealed, 24-month warranty.

Saved items Sign in
Thermal pad sheet and braided PSU cable kit with combs

myVolts

myVolts Thermal Pad 12.8 W/mK 85x45x1mm + PSU Sleeved Cable Kit 18AWG 30cm

SKU CH-QTG8-9EVF8

High-conductivity thermal pad rated at 12.8 W/mK measuring 85 by 45 by 1 mm bundled with sleeved 18AWG PSU extension cables including 24-pin ATX, 4+4-pin EPS.

  • TypeAT
  • High thermal conductivity of 12.8 W/mK moves heat from components in seconds
  • Operating range from -40 to 200 °C ensures stability under extreme loads
  • Non-conductive silicone pad prevents short circuits on exposed traces
  • 18 AWG copper strands with triple-layer braid deliver reliable power and clean routing
  • Kit includes 24-pin ATX, 4+4-pin EPS, two 8-pin and two 6-pin PCIe cables

Thermal pad for memory and chipset cooling

This kit includes a high-conductivity thermal pad measuring 85 by 45 by 1 millimetres with a rating of 12.8 W/mK. It targets builders who need to bridge gaps between memory modules, voltage regulators or chipset heatsinks and their coolers. The pad is non-conductive, operates from minus 40 to 200 degrees Celsius and can be cut to fit specific layouts.

Replaces stock pads or thermal paste on dense boards

Factory pads often use lower-conductivity material that cannot move heat quickly enough from tightly packed components. The 12.8 W/mK rating and 3.1 g/cc density deliver a measurable improvement when the original interface is too thick or has dried out. The jump is worth it when temperatures on memory or VRM zones remain high despite adequate airflow.

Sustained load behaviour with included cable kit

The silicone rubber retains its elasticity and compression characteristics during prolonged heat soak, resisting pump-out and hardening. Density remains stable at 3.1 g/cc and hardness stays within 30 to 55 Shore C after repeated cycles. The bundled 18 AWG sleeved extensions — 24-pin ATX, 4+4-pin EPS, two 8-pin and two 6-pin PCIe at 30 centimetres — keep power delivery tidy without adding resistance that could affect long-term stability.

Highlights

  • High thermal conductivity of 12.8 W/mK moves heat from components in seconds
  • Operating range from -40 to 200 °C ensures stability under extreme loads
  • Non-conductive silicone pad prevents short circuits on exposed traces
  • 18 AWG copper strands with triple-layer braid deliver reliable power and clean routing
  • Kit includes 24-pin ATX, 4+4-pin EPS, two 8-pin and two 6-pin PCIe cables

Specifications

TypeAT

Questions about this item

What gap thickness does the 85x45mm thermal pad fill?

The pad is 1mm thick and can be cut to size, so it fills gaps up to 1mm between the component and heatsink.

How are the 18AWG sleeved cables routed for a clean install?

Route each 30cm extension — 24-pin ATX, 4+4-pin EPS, two 8-pin and two 6-pin PCIe — then snap the included combs onto the cables to lock spacing and improve airflow.

When should the thermal pad be replaced?

The silicone pad is rated from -40 to 200 °C and resists drying out; replace only if it tears, loses compression or shows visible degradation during a rebuild.

New to this? Which coin should you pay with — what to check, what it costs to pay, and what is never asked for.

Also in this aisle

People compared these

Same shelf, same checkout — eight coins and a 30-minute rate lock.