We take cryptocurrency — so the coins you hold can buy real hardware.Pay in crypto, spend it on real hardware. Free insured shipping worldwide over $399. Plain, unbranded boxes, sent from Germany.Free insured shipping over $399. Your rate is locked for 30 minutes once checkout opens.Rate locked 30 minutes. Every item sealed, serial-checked and covered by a 24-month warranty.Sealed, 24-month warranty.

Saved items Sign in
Black steel front wheel hub assembly with square flange and ABS sensor cable

Moog

Moog Front Wheel Bearing Hub Assembly Ford F-250 F-350 Super Duty Excursion 4X4

SKU CH-AZ5R-YBD0K

Front wheel bearing hub assembly with ABS sensor and wiring harness fits 2000-2004 Ford F-250, F-350 Super Duty and Excursion 4X4 models

  • ColorBlack
  • Direct-fit replacement for 2000-2004 Ford Super Duty and Excursion 4X4 models
  • Integrated ABS sensor with 60-tooth tone ring maintains factory braking performance
  • Pre-assembled hub unit with 55-spline driven design installs without separate bearing service
  • 85-inch wiring harness and round connector match original equipment routing
  • Steel construction with tapered bearings supports 7.992-inch hub diameter and 5.661-inch height

Front Wheel Hub for Super Duty 4X4

This Moog front wheel bearing hub assembly fits 2000 through 2004 Ford F-250 and F-350 Super Duty trucks plus the 2000 to 2002 Excursion with four-wheel drive. The unit includes the ABS sensor, a round connector and a 46.85 inch wiring harness ready for either the driver or passenger side.

Replaces worn original hub with integrated ABS

A direct swap for the factory driven hub on the listed models, it uses a 55-spline design and a 60-tooth tone ring that matches the original ABS signalling. The upgrade is worth it when the original bearing develops play, the ABS light triggers from a damaged ring or the wheel speed sensor fails and the harness is corroded.

Tapered roller bearing with 4-bolt knuckle mounting

The hub mounts to the knuckle with four bolts and supplies eight M14-2.0 lug bolts plus eight M14-1.50 flange bolts. Hub centre bore is 170mm, flange offset is 54.5mm and total hub height is 143.8mm. These fixed dimensions mean the assembly only fits the specified Super Duty and Excursion 4X4 applications; it will not work on two-wheel-drive models or later model years.

Highlights

  • Direct-fit replacement for 2000-2004 Ford Super Duty and Excursion 4X4 models
  • Integrated ABS sensor with 60-tooth tone ring maintains factory braking performance
  • Pre-assembled hub unit with 55-spline driven design installs without separate bearing service
  • 85-inch wiring harness and round connector match original equipment routing
  • Steel construction with tapered bearings supports 7.992-inch hub diameter and 5.661-inch height

Specifications

ColorBlack

Questions about this item

What bolt pattern and centre bore does the 203 mm flange need to match on my 2002 F-250 Super Duty?

The flange uses eight M14-1.50 bolts on a 61.2 mm circle and a 170 mm centre bore to match the factory knuckle.

How do I install the hub assembly and which step is most often missed?

Bolt the unit to the knuckle with four M14-2.0 bolts, torque to spec, then seat the axle splines fully before tightening the axle nut — skipping the spline seat causes noise.

When will the ABS tone ring or sensor need attention on this 55-spline driven hub?

The 60-tooth tone ring is pressed into the hub; if the ABS light appears, inspect the round connector and 46.85 in harness for corrosion or wire damage.

Also in this aisle

People compared these

Same shelf, same checkout — eight coins and a 30-minute rate lock.