We take cryptocurrency — so the coins you hold can buy real hardware.Pay in crypto, spend it on real hardware. Free insured shipping worldwide over $399. Plain, unbranded boxes, sent from Germany.Free insured shipping over $399. Your rate is locked for 30 minutes once checkout opens.Rate locked 30 minutes. Every item sealed, serial-checked and covered by a 24-month warranty.Sealed, 24-month warranty.

Saved items Sign in
Small white flux syringe with copper desoldering braid spool

Meterk TH-338 Solder Flux Paste 5ml & Solder Wick Braid 10ft Kit

SKU CH-TP4H-JWDDJ MPN TH-338

A 5 ml no-clean rosin flux paste with plunger dispenser and 10 ft oxygen-free copper desoldering braid for electronics repair

  • TypeAdhesives
  • Size/Dimensions2.4892 cm x 8.4074 cm x 15.0114 cm
  • FeaturesFlux*1, Solder Wick*1, Push rod*1, Needle*3
  • No-clean flux leaves zero residue on boards
  • Highly active rosin paste removes oxide layers instantly
  • Plunger dispenser gives precise flux control, cuts waste
  • Oxygen-free copper wick absorbs excess solder fast
  • Kit covers BGA, SMT, phone and appliance repairs

Solder Flux Paste & Desoldering Wick Kit

The Meterk TH-338 kit combines a 5 ml no-clean rosin flux paste with a 10 ft oxygen-free copper desoldering braid. It is intended for technicians and hobbyists who repair phone PCBs, BGA packages, SMD components and general consumer electronics. A plunger syringe, three needles and a push rod are included for controlled flux dispensing.

Flux Activity & Braid Limits

The rosin flux is RoHS compliant, leaves no residue and produces low smoke, but its activity level suits standard leaded and lead-free solders only; heavily oxidised or high-temperature joints may need a more aggressive chemistry. The braid width is .1 in and relies on thermal transfer from the iron tip, so very large ground planes or multi-layer boards can exceed its absorption speed.

Installation & Common Issues

Apply flux through the needle, heat the joint with the iron, then lay the wick on the molten solder and remove both together once saturated. Cut off the used section with side cutters. Problems arise if the iron temperature is too low, the wick is moved before full absorption, or excess flux is left on sensitive high-impedance circuits.

Highlights

  • No-clean flux leaves zero residue on boards
  • Highly active rosin paste removes oxide layers instantly
  • Plunger dispenser gives precise flux control, cuts waste
  • Oxygen-free copper wick absorbs excess solder fast
  • Kit covers BGA, SMT, phone and appliance repairs

Specifications

BrandMeterk
Model2 Pack Kit
TypeAdhesives
Size/Dimensions2.4892 cm x 8.4074 cm x 15.0114 cm
FeaturesFlux*1, Solder Wick*1, Push rod*1, Needle*3

Questions about this item

Is the 5 ml flux syringe and 10 ft wick spool enough for occasional phone board repairs?

The 5 ml flux syringe and 10 ft desoldering wick cover many small BGA or SMT jobs; the plunger gives precise flux control and the wick cuts cleanly after each use.

How does the rosin flux behave when I heat a joint on a mobile phone PCB?

The milky-white rosin flux removes oxide layers quickly, wets the joint well, produces low smoke and leaves no residue so no cleaning is needed.

What does the 0.1 in width of the copper braid limit in practice?

The 0.1 in wide oxygen-free copper braid fits tight SMD pads and absorbs excess solder fast, but wider joints need multiple passes.

Also in this aisle

People compared these

Same shelf, same checkout — eight coins and a 30-minute rate lock.