We take cryptocurrency — so the coins you hold can buy real hardware.Pay in crypto, spend it on real hardware. Free insured shipping worldwide over $399. Plain, unbranded boxes, sent from Germany.Free insured shipping over $399. Your rate is locked for 30 minutes once checkout opens.Rate locked 30 minutes. Every item sealed, serial-checked and covered by a 24-month warranty.Sealed, 24-month warranty.

Saved items Sign in
Flat ribbon cable with 36-pin SFF-8643 connector splitting to four SATA plugs, woven mesh sheath on half length

Marchez Vous

Marchez Vous Mini SAS SFF-8643 to 4 SATA Cable 1.6ft

SKU CH-72R3-QGZ9K

Internal 36-pin SFF-8643 to four 7-pin SATA breakout cable, 1.6ft long, links a 12 Gbps RAID controller to 2.5 or 3.5 inch SATA I, II.

  • TypeRadios
  • Connect 12 Gbps RAID controller to four SATA drives via 36 pin SFF-8643
  • Supports 3 Gbps and 6 Gbps SATA drives during 12 Gbps storage migration
  • 6 ft flat ribbon cable with acetate cloth tape for strain relief
  • Low profile SATA connectors with stainless steel latches prevent accidental disconnection
  • RoHS compliant 30 AWG cable compatible with 2.5 and 3.5 inch drives

Marchez Vous SFF-8643 to SATA Cable

This Marchez Vous cable connects a 12 Gbps host bus adapter or RAID controller with a 36 pin SFF-8643 port to four SATA drives. The 1.6ft breakout design uses 30 AWG flat ribbon wire under acetate cloth tape and a woven mesh sheath. Low profile SATA connectors feature stainless steel latches and P1 to P4 markers for identification. It supports 2.5 and 3.5 inch SATA I, II, III hard drives.

Woven sheath and marked connectors

The woven mesh covers half the cable length to assist routing inside a chassis without adding rigidity. Acetate cloth tape provides strain relief on the slim ribbon cables. Stainless steel latches on each SATA plug resist accidental disconnection and reduce vibration. Printed P1 to P4 markers on the connectors simplify drive identification after installation is complete.

Verify controller and drive compatibility

Data transfer speed depends on the capabilities of your SAS controller and the installed SATA drives. This cable carries data only; a separate power splitter cable is required to supply power to the four drives. Ensure your RAID controller or HBA presents an SFF-8643 male port and that the target drives use standard 7 pin SATA data connectors.

Highlights

  • Connect 12 Gbps RAID controller to four SATA drives via 36 pin SFF-8643
  • Supports 3 Gbps and 6 Gbps SATA drives during 12 Gbps storage migration
  • 6 ft flat ribbon cable with acetate cloth tape for strain relief
  • Low profile SATA connectors with stainless steel latches prevent accidental disconnection
  • RoHS compliant 30 AWG cable compatible with 2.5 and 3.5 inch drives

Specifications

TypeRadios

Questions about this item

Does the 30 AWG ribbon cable need periodic replacement in a 24/7 server?

The cable is built for continuous 24/7 operation with acetate cloth tape and a woven mesh sheath that provide strain relief and protect the conductors, so no scheduled replacement is required.

What throughput ceiling appears first when four SATA III drives run flat out through the single SFF-8643 link?

The SFF-8643 host connector supports 12 Gbps aggregate bandwidth, while each SATA III drive caps at 6 Gbps, so the host link becomes the bottleneck before any individual drive saturates.

How much heat or fan noise does the cable assembly add when the drives run all day?

The passive 30 AWG ribbon with mesh sheathing generates no measurable heat and adds zero acoustic noise; only the drives and controller fans contribute to temperature and sound.

Also in this aisle

People compared these

Same shelf, same checkout — eight coins and a 30-minute rate lock.