MakerBot
MakerBot MP06572 PLA filament 10-pack 1.75 mm
Ten spools of 1.75 mm PLA filament in assorted colours, each weighing 0.9 kg, for MakerBot Replicator printers
- ColorTrue Green True Blue True Purple True White True Red True Or
- MaterialPLA plastic
- Diameter1.75 mm
- Compatible SystemMakerBot Replicator 5th-Generation Printers MakerBot Replica
- FeaturesPackaged Quantity: 10
- LengthSpool Diameter : 9.84" / 25.00 cm Spool Width: 1.57" / 4.00
- Ten colours in one pack give immediate variety
- 75 mm diameter works with Replicator 2, 5th-Gen and Z18 printers
- PLA material prints without a heated bed and reduces warping
- Non-toxic corn-based resin is safe for beginners and classrooms
- Each 2.0 lb spool provides long print runs
Ten-colour PLA pack for MakerBot printers
This 10-spool assortment supplies True Green, True Blue, True Purple, True White, True Red, True Orange, True Yellow, Cool Gray, Warm Gray and True Black PLA filament. Each spool is 1.75 mm diameter and weighs 2.0 lbs. The pack is built for MakerBot Replicator 5th-Generation, Replicator Z18 and Replicator 2 printers.
Low-warp material prints without a heated bed
PLA shows much less warping and curling than ABS, so successful prints are possible on unheated build plates. The resin is derived from field corn, nontoxic and gives off a semi-sweet waffle-like smell when heated. Sharp corners and edges reproduce well with a glossy finish.
Spools fit standard MakerBot hubs
Every spool measures 9.84 inches in diameter, 1.57 inches wide with a 2.00 inch hub hole, matching the Replicator spool holder. The 10-pack delivers 0.9 kg per colour for extended multi-colour projects. Buyers needing other diameters or non-MakerBot printers should look elsewhere.
Highlights
- Ten colours in one pack give immediate variety
- 75 mm diameter works with Replicator 2, 5th-Gen and Z18 printers
- PLA material prints without a heated bed and reduces warping
- Non-toxic corn-based resin is safe for beginners and classrooms
- Each 2.0 lb spool provides long print runs
Specifications
| Brand | Makerbot |
|---|---|
| Model | MP06572 |
| Color | True Green True Blue True Purple True White True Red True Orange True Yellow Cool Gray Warm Gray True Blac |
| Material | PLA plastic |
| Diameter | 1.75 mm |
| Compatible System | MakerBot Replicator 5th-Generation Printers MakerBot Replicator Z18 Printers MakerBot Replicator 2 Printers |
| Features | Packaged Quantity: 10 |
| Length | Spool Diameter : 9.84" / 25.00 cm Spool Width: 1.57" / 4.00 cm Spool Hub Hole: 2.00" / 5.08 cm Diameter: 0.068" / 0.175 cm |
| Weight | 2.0 lbs / 0.9 kg (Each spool) |
| Shipping weight | 13.61 kg |
| Package size | 457 × 254 × 254 mm |
Questions about this item
How do I load the 1.75 mm spool onto a Replicator 5th-Generation printer and what step causes jams?
Place the spool on the holder so filament unwinds counter-clockwise, feed it into the guide tube until the extruder gears grab, then run the load script; skipping the counter-clockwise orientation makes the filament cross-thread and jam.
What will need replacement after printing several kilograms on a Replicator Z18?
The brass nozzle wears from abrasive pigments in the True Color PLA, so plan to swap it every few kilograms; the PTFE guide tube also stiffens with heat cycles and should be changed when retraction becomes inconsistent.
What limit appears first during a long print on a Replicator 2?
The 0.9 kg spool runs out before thermal limits are reached, so the practical ceiling is the 2.0 lb capacity per colour.
Also in this aisle
People compared these
Same shelf, same checkout — eight coins and a 30-minute rate lock.
CHIEF MANUFACTURING
CHIEF MANUFACTURING CMS018 18" 457 mm Fixed Extension Column projector accessory
- Extension Column
- Projector
$22.99$22.99
0.0002665BTC
In stock