We take cryptocurrency — so the coins you hold can buy real hardware.Pay in crypto, spend it on real hardware. Free insured shipping worldwide over $399. Plain, unbranded boxes, sent from Germany.Free insured shipping over $399. Your rate is locked for 30 minutes once checkout opens.Rate locked 30 minutes. Every item sealed, serial-checked and covered by a 24-month warranty.Sealed, 24-month warranty.

Saved items Sign in
Compact silver DAC headphone amp with USB-C optical RCA and dual 3.5 6.35 mm jacks

LORDWORLD

LORDWORLD K5 USB DAC Headphone Amplifier Streaming Audio

SKU CH-01XV-V2G3F

A USB DAC and headphone amplifier with optical input, dual 6.35/3.5mm outputs and ESS9038Q2M decoding up to PCM 32bit/384kHz and DSD256

  • Ultra-low distortion 0.0007% THD from ESS9038Q2M DAC
  • 121dB signal-to-noise ratio for ultra-pure sound
  • 560mW and 470mW at 32 ohms drives demanding headphones
  • High and low gain modes suit 16 to 600 ohm loads
  • USB and optical inputs plus RCA, 6.35mm and 3.5mm outputs

LORDWORLD K5 USB DAC Amp

The LORDWORLD K5 is a USB DAC and headphone amplifier that adds optical input and multiple analogue outputs to a computer or Mac. It serves as a preamp, a USB-to-optical converter and a headphone driver for listeners who want higher fidelity than built-in audio. The ESS9038Q2M DAC, SA9312 DSP, OPA1678 LPF and SGM8262 amp chips handle PCM 32bit/384kHz and DSD256 decoding. Signal-to-noise ratio exceeds 121dB with THD of 0.0007% and a 3V noise floor.

Upgrade from onboard audio

This unit replaces a motherboard headphone jack or basic USB dongle when you need optical connectivity, RCA line outputs or more driving power. The jump is worth it if you own headphones between 16 and 600 ohms and want 560mW or 470mW per channel at 32 ohms with selectable high and low gain. It also adds a pure bypass mode that removes tone controls for uncoloured playback. Buyers who need balanced XLR outputs or network streaming cannot use this device.

Desktop USB-C setup

Connect the K5 via USB-C for power and data, then plug headphones into the 6.35mm or 3.5mm jacks and speakers into RCA or optical outputs. A gain switch matches impedance and a tone-control bypass keeps the signal path clean. Common issues include forgetting to select the correct digital input on the source device and setting system volume too low before raising the amp gain, which can raise the noise floor.

Highlights

  • Ultra-low distortion 0.0007% THD from ESS9038Q2M DAC
  • 121dB signal-to-noise ratio for ultra-pure sound
  • 560mW and 470mW at 32 ohms drives demanding headphones
  • High and low gain modes suit 16 to 600 ohm loads
  • USB and optical inputs plus RCA, 6.35mm and 3.5mm outputs

Specifications

BrandLORDWORLD

Questions about this item

What connectors and space does the K5 need on my desk?

The K5 uses a USB Type-C input, an SPDIF optical input, and provides optical, RCA, 6.35 mm and 3.5 mm outputs. It is a compact desktop unit that only requires a flat surface and access to those ports.

How do I connect the K5 to my computer and headphones, and what setting do people forget?

Plug the USB Type-C cable into your computer, connect headphones to the 6.35 mm or 3.5 mm jack, then select the correct gain mode — high for 16–600 ohm loads, low for sensitive models — and set the tone switch to PURE if you want a flat response.

Which parts of the K5 will wear out or need replacement over time?

The K5 has no user-replaceable tubes, batteries or moving parts. The ESS9038Q2M DAC, SA9312 DSP, OPA1678 LPF and SGM8262 amplifier are soldered in place, so long-term service would require a technician rather than a simple swap.

Also in this aisle

People compared these

Same shelf, same checkout — eight coins and a 30-minute rate lock.