We take cryptocurrency — so the coins you hold can buy real hardware.Pay in crypto, spend it on real hardware. Free insured shipping worldwide over $399. Plain, unbranded boxes, sent from Germany.Free insured shipping over $399. Your rate is locked for 30 minutes once checkout opens.Rate locked 30 minutes. Every item sealed, serial-checked and covered by a 24-month warranty.Sealed, 24-month warranty.

Saved items Sign in
Silver rectangular car amplifier with heat-sink fins, LED indicators and RCA terminals

Lanzar

Lanzar VCT4110 2000W 4-Channel Class AB Car Amplifier

SKU CH-XWB2-H238F MPN VCT4110

Four-channel Class AB car amplifier delivering 500W per channel at 4 ohms, bridgeable to 1000W per pair at 2 ohms, with variable crossovers from 40 to 250 Hz and bass boost up to 18 dB

  • Amplifier ClassClass AB
  • Amplifier Channels4 Channels
  • TypeAmplifier
  • Max Power2000W
  • Frequency Response30 kHz
  • BridgeableYes
  • 2000W max power drives demanding speaker setups
  • 500W RMS per channel at 4 ohms delivers clean output
  • Bridgeable to 1000W x 2 at 2 ohms for flexible configurations
  • 15 Hz–30 kHz frequency response covers full audible range
  • Thermal, overload and short-circuit protection safeguards the amplifier

High-Power 4-Channel Amplifier

The Lanzar VCT4110 is a Class AB car amplifier built to drive a four-speaker system with up to 2000W maximum power. It delivers 500W per channel at 4 Ohms and can be bridged to produce 1000W per pair at 2 Ohms. A MOSFET power supply and 2 Ohm stable operation support demanding audio setups.

System Builders Needing Flexible Configuration

This amplifier suits installers who want a single unit for full-range or component systems with adjustable crossovers. Variable high-pass and low-pass filters from 40 Hz to 250 Hz plus a 0-18dB bass boost allow detailed tuning. Buyers requiring more than four channels or a Class D design for higher efficiency should consider other options.

16 Ohm Load Impedance Capability

The specifications list a 16 Ohm load impedance capability alongside standard 4 Ohm and 2 Ohm ratings. This figure determines whether the amplifier can safely drive high-impedance speakers or specific wiring configurations without overheating. Verify your speaker impedance matches this rating before purchase.

Highlights

  • 2000W max power drives demanding speaker setups
  • 500W RMS per channel at 4 ohms delivers clean output
  • Bridgeable to 1000W x 2 at 2 ohms for flexible configurations
  • 15 Hz–30 kHz frequency response covers full audible range
  • Thermal, overload and short-circuit protection safeguards the amplifier

Specifications

BrandLanzar
SeriesVector
Amplifier ClassClass AB
Amplifier Channels4 Channels
TypeAmplifier
Max Power2000W
Frequency Response30 kHz
BridgeableYes
Load Impedance Capability16 Ohm
Dimensions1.78 X 10.63 X 14.02
Shipping weight5.09 kg
Package size356 × 270 × 45 mm

Questions about this item

How much continuous power can the VCT4110 deliver before thermal protection activates?

The amplifier is rated at 500W x 4 channels at 4 ohms RMS; sustained output at that level will eventually trigger the built-in thermal protection circuit.

What are the noise and heat characteristics when the VCT4110 runs all day?

Signal-to-noise ratio exceeds 95dB and THD is 0.1%; the Class AB design generates noticeable heat, so adequate airflow around the 1.78 x 10.63 x 14.02 inch chassis is required.

What wiring and fuses must I already have to install this amplifier?

You need 4-gauge power and ground wire, a pair of 30A maxi fuses for the dual fuse holders, RCA cables for low-level input, and speaker wire for 4-ohm or 2-ohm loads.

Also in this aisle

People compared these

Same shelf, same checkout — eight coins and a 30-minute rate lock.