We take cryptocurrency — so the coins you hold can buy real hardware.Pay in crypto, spend it on real hardware. Free insured shipping worldwide over $399. Plain, unbranded boxes, sent from Germany.Free insured shipping over $399. Your rate is locked for 30 minutes once checkout opens.Rate locked 30 minutes. Every item sealed, serial-checked and covered by a 24-month warranty.Sealed, 24-month warranty.

Saved items Sign in
Five white cables with red green white wires and three pin JST SM plugs

KEHIPI

KEHIPI 5 Pcs 20AWG 3 Pin JST SM Extension Cable 1m

SKU CH-P1ZV-B9VMR

Five 1 m JST SM male-to-female cables extend WS2811, WS2812B, WS2814, SK6812 or FCOB RGB strips and SP-series controllers without soldering

  • Color MappingWhite
  • Solder-free installation with male-to-female JST SM connectors
  • Extend LED strips or controllers up to 3.28 feet
  • Pre-wired 20 AWG cable rated for 5 V to 24 V systems
  • Compatible with WS2811, WS2812, WS2814 and SK6812 addressable LEDs
  • Works with SP105, SP107, SP108, SP530, SP602, SP630 and SP638 controllers

JST SM Extension Cable Kit

This five-pack of 20AWG three-pin JST SM male-to-female cables extends low-voltage LED strip runs by one metre each. Builders wiring WS2811, WS2812B, WS2814, SK6812 or FCOB WS2811 addressable strips can bridge gaps between segments or link strips to SP-series controllers without soldering. The red, green and white conductors carry power, data and ground in the standard JST SM pinout.

Solderless Flexible Wiring

Each cable arrives with pre-crimped connectors that plug directly into compatible strip ends and controller headers, so installation needs only a push-fit. The wires can be trimmed to any shorter length and re-used with new connectors if the project layout changes. Because the set includes both male and female ends, it supports strip-to-strip chains as well as controller-to-strip links in a single pack.

Low-Voltage Signal Limits

The supplier notes that signal instability and voltage drop may appear on long runs, showing as irregular flickering or dimmed output. The cables are rated for 5V to 24V low-voltage circuits only and must not be used on mains-voltage wiring. Polarity must be verified before power is applied because the colour mapping uses white instead of the more common blue for the data line.

Highlights

  • Solder-free installation with male-to-female JST SM connectors
  • Extend LED strips or controllers up to 3.28 feet
  • Pre-wired 20 AWG cable rated for 5 V to 24 V systems
  • Compatible with WS2811, WS2812, WS2814 and SK6812 addressable LEDs
  • Works with SP105, SP107, SP108, SP530, SP602, SP630 and SP638 controllers

Specifications

BrandBTF-LIGHTING
Color MappingWhite

Questions about this item

Will the 20AWG wires need replacement after repeated bending during LED strip installations?

The 20AWG stranded conductors are flexible enough for routing around corners; inspect the insulation for cuts if cables are moved frequently, but no scheduled replacement is required.

At what cable length does voltage drop first cause flickering on WS2812B strips?

The manufacturer notes that signal instability and voltage drop may appear on long extension runs; the 1 metre length supplied is within typical low-voltage limits, but chaining multiple cables can exceed the 5V–24V tolerance and cause irregular flickering.

How warm do the JST SM connectors get when powering RGB strips at 24V all day?

The connectors are rated for the 5V–24V low-voltage range used by WS2811, WS2812B, WS2814 and SK6812 strips; under normal continuous load they remain cool to the touch, though excessive current beyond the 20AWG capacity would increase heat.

Also in this aisle

People compared these

Same shelf, same checkout — eight coins and a 30-minute rate lock.