We take cryptocurrency — so the coins you hold can buy real hardware.Pay in crypto, spend it on real hardware. Free insured shipping worldwide over $399. Plain, unbranded boxes, sent from Germany.Free insured shipping over $399. Your rate is locked for 30 minutes once checkout opens.Rate locked 30 minutes. Every item sealed, serial-checked and covered by a 24-month warranty.Sealed, 24-month warranty.

Saved items Sign in
Five male-to-female JST SM cables with red green white 20AWG wires 1.5m long

KEHIPI

KEHIPI 3PIN-SM-20AWG-150CM-MF-5P 5-pack 3-pin JST SM 20AWG 1.5m extension cable

SKU CH-M1QQ-6EYPD MPN 3PIN-SM-20AWG-150CM-MF-5P

Five 1.5 m male-to-female JST SM cables extend 3-pin addressable LED strips or controllers without soldering

  • ColorMulti-colored
  • SpecificationsBTF-LIGHTING
  • Connect strip-to-strip or controller-to-strip with male-to-female JST SM plugs
  • 5 m length per cable gives flexible routing in low-voltage installations
  • 20 AWG wire supports 5 V to 24 V addressable LED runs without soldering
  • Compatible with WS2811, WS2812B, WS2814, SK6812 and FCOB strips
  • Five-pack supplies multiple extensions for larger lighting projects

JST SM 3-pin extension cable 5-pack

This pack contains five male-to-female extension cables with a 3-pin JST SM connector. Each cable uses 20AWG wire and measures 1.5 metres (4.92 feet). They are designed for low-voltage addressable LED strips and controllers that use a three-wire connection. The cables arrive ready to use without soldering.

Capacity and voltage limits

The cables operate within a 5V to 24V low-voltage range and suit WS2811, WS2812B, WS2814, SK6812 and FCOB WS2811 IC RGB strips. They also connect to SP105E, SP107E, SP108E, SP602E, SP530E, SP630E, SP638E, DR03W and DR04W controllers. Signal instability or voltage drop may appear on longer runs, causing flicker or dimming.

Replaces soldered joints and short leads

These extensions replace the need to solder wires between strips or between a strip and a controller. They are not suited for installations that require a four-pin or two-pin connector, nor for runs where the 1.5 metre length introduces unacceptable signal loss. Builders who need longer continuous lengths without intermediate connectors should consider a different wiring approach.

Highlights

  • Connect strip-to-strip or controller-to-strip with male-to-female JST SM plugs
  • 5 m length per cable gives flexible routing in low-voltage installations
  • 20 AWG wire supports 5 V to 24 V addressable LED runs without soldering
  • Compatible with WS2811, WS2812B, WS2814, SK6812 and FCOB strips
  • Five-pack supplies multiple extensions for larger lighting projects

Specifications

BrandBTF-LIGHTING
Model3PIN-SM-20AWG-150CM-MF-5P
ColorMulti-colored
SpecificationsBTF-LIGHTING

Questions about this item

Will the 1.5 m JST SM cable reach from my existing SP108E controller to the WS2812B strip without signal issues?

The 1.5 m extension is rated for 5 V–24 V low voltage and fits SP108E controllers and WS2812B strips; the supplier notes that very long runs may show flicker or voltage drop, so keep the total length as short as practical.

How can I confirm the 3-pin JST SM connectors are seated correctly after plugging them in?

The red, green and white wires map to power, data and ground — verify the strip lights up with steady colour and no flicker, then tug gently to ensure the male and female housings are fully latched.

The pack lists five 1.5 m cables with male and female ends — do I need any extra connectors or solder?

Each of the five cables already includes a male-to-female JST SM pair, and the wires can be trimmed to length without soldering; no additional connectors are required for standard strip-to-strip or controller-to-strip links.

Also in this aisle

People compared these

Same shelf, same checkout — eight coins and a 30-minute rate lock.