We take cryptocurrency — so the coins you hold can buy real hardware.Pay in crypto, spend it on real hardware. Free insured shipping worldwide over $399. Plain, unbranded boxes, sent from Germany.Free insured shipping over $399. Your rate is locked for 30 minutes once checkout opens.Rate locked 30 minutes. Every item sealed, serial-checked and covered by a 24-month warranty.Sealed, 24-month warranty.

Saved items Sign in
Two black 11.8in ARGB extension cables with 5V 3-pin female connectors and four male plugs

Jstincal 2-Pack 11.8in ARGB Extension Cable 5V 3-Pin Female to Female Splitter

SKU CH-QE8N-MZZYG

Two 11.8-inch 5 V 3-pin ARGB extension cables with included male connectors extend addressable RGB fans or LED strips from a motherboard header

  • TypeBlack
  • ColorBlack
  • Connector Detail3-pin Argb to Female-to-Female
  • Terminal GenderFemale to Female
  • SpecificationsBlack, 11.8 L x 0.5 W x 0.2 H inches
  • ShieldingBlack
  • Extends ARGB fans and LED strips with 11.8 inch reach
  • Two cables included for dual-zone lighting setups
  • 5 V three-pin addressable RGB header compatibility only
  • Tool-free plug-and-play install with supplied male connectors
  • Genuine copper cores carry addressable RGB signals reliably

ARGB 5 V 3-Pin Extension Kit

This two-pack of 11.8-inch cables extends addressable RGB fans or LED strips from a motherboard 5 V 3-pin ARGB header. Each cable runs female-to-female and includes separate 3-pin male connectors for tool-free assembly. The pair suits builders adding synchronized lighting to an existing ARGB loop.

Upgrade from short factory leads

Factory fan cables often fall short of the header in mid-tower or full-tower chassis, forcing awkward routing or daisy-chain limits. These extensions bridge the gap when the stock length cannot reach the motherboard ARGB connector. The jump is worth it whenever cable strain or hidden routing would otherwise compromise the lighting layout.

Plug-and-play with arrow alignment

No soldering or crimping is required; the supplied male pins snap into the female ends once the arrows on both connectors line up. Misaligned arrows are the usual cause of missing colours or flickering strips, so verify orientation before seating the plugs. Route the slender 0.5-inch-wide cables behind the motherboard tray to keep airflow paths clear.

Highlights

  • Extends ARGB fans and LED strips with 11.8 inch reach
  • Two cables included for dual-zone lighting setups
  • 5 V three-pin addressable RGB header compatibility only
  • Tool-free plug-and-play install with supplied male connectors
  • Genuine copper cores carry addressable RGB signals reliably

Specifications

BrandJstincal
TypeBlack
ColorBlack
Connector Detail3-pin Argb to Female-to-Female
Terminal GenderFemale to Female
SpecificationsBlack, 11.8 L x 0.5 W x 0.2 H inches
ShieldingBlack
ConstructionARGB
FeaturesBlack
Disclaimernot_applicable

Questions about this item

How much clearance do the 11.8 inch cables and 0.5 inch wide connectors need behind the motherboard tray?

Each cable is 11.8 inches long and the connectors are 0.5 inches wide, so allow at least that much depth behind the tray for routing.

Which way round do the 3 pin male connectors go on the 5V ARGB header?

Align the arrow on each male connector with the arrow on the motherboard +5V 3 pin ARGB header, then press straight in.

When should the copper cores inside the 11.8 inch extensions be checked or replaced?

Inspect the copper cores if LED colours flicker or drop out; replace a cable if the insulation is cracked or pins are bent.

New to this? Which coin should you pay with — what to check, what it costs to pay, and what is never asked for.

Also in this aisle

People compared these

Same shelf, same checkout — eight coins and a 30-minute rate lock.