We take cryptocurrency — so the coins you hold can buy real hardware.Pay in crypto, spend it on real hardware. Free insured shipping worldwide over $399. Plain, unbranded boxes, sent from Germany.Free insured shipping over $399. Your rate is locked for 30 minutes once checkout opens.Rate locked 30 minutes. Every item sealed, serial-checked and covered by a 24-month warranty.Sealed, 24-month warranty.

Saved items Sign in
Stainless steel pressure transducer with 3-pin Packard connector, IP67 rated

Johnson Controls Inc

Johnson Controls P599RCPS105C Pressure Transducer 0-500 psi 304L SS

SKU CH-XDFG-W96WS

Measures 0 to 500 psi with a 0.5 to 4.5V DC output and IP67-rated 304L stainless steel housing

  • Accurate readings across a 0 to 500 psi range with ±1.50% precision
  • Wide -40 °F to 212 °F operating span handles extreme environments
  • IP67-rated 304L stainless steel housing resists water and corrosion
  • 5 to 4.5 V DC output on a 4.75 to 5.25 V supply simplifies integration
  • SAE 45° flare male port and 3-pin Packard connector enable quick installation

Pressure transducer for 0 to 500 psi systems

The Johnson Controls P599RCPS105C measures pressure from 0 to 500 psi and outputs a 0.5 to 4.5V DC signal. It uses a 3-pin Packard connector with two wires and a male SAE 45-degree flare process connection sized at 1/4 in. The housing is 304L stainless steel and rated IP67 for ingress protection.

Thermal range and power requirements

The transducer operates between -40 and 212 degrees F, covering freezing and high-temperature environments. It requires a supply voltage of 4.75 to 5.25V DC and delivers an accuracy of +/- 1.50 percent across the range. The IP67 rating ensures the electronics remain sealed during normal wash-down or outdoor exposure.

Sustained load behaviour

Under continuous pressure the output remains stable within the stated accuracy band and the stainless steel housing resists corrosion from prolonged media contact. The sealed construction maintains the IP67 rating over time, preventing moisture ingress during extended duty cycles. The fixed voltage supply range supports consistent operation without drift.

Highlights

  • Accurate readings across a 0 to 500 psi range with ±1.50% precision
  • Wide -40 °F to 212 °F operating span handles extreme environments
  • IP67-rated 304L stainless steel housing resists water and corrosion
  • 5 to 4.5 V DC output on a 4.75 to 5.25 V supply simplifies integration
  • SAE 45° flare male port and 3-pin Packard connector enable quick installation

Specifications

BrandJOHNSON CONTROLS

Questions about this item

How do I install the 1/4 in SAE 45° flare male process connection and 3-pin Packard connector correctly?

Thread the 1/4 in SAE 45° flare male fitting into the matching female port using the proper wrench size, then push the 3-pin Packard connector firmly until it clicks; the step most often missed is fully seating the connector latch so the 0.5 to 4.5V DC signal stays stable.

What maintenance or replacement will the stainless steel housing and IP67 seal need over time?

Inspect the 304L stainless steel housing and IP67 seal annually for corrosion or cracking; replace the transducer if the +/- 1.50 % accuracy drifts beyond tolerance or if the 4.75 to 5.25V DC supply cannot maintain a steady 0.5 to 4.5V DC output.

At what point does the -40 to 212 °F temperature limit affect sustained operation first?

Continuous exposure near the 212 °F upper limit will degrade the internal electronics and seals before the -40 °F low end becomes an issue, causing output drift outside the +/- 1.50 % spec and eventual signal loss.

Also in this aisle

People compared these

Same shelf, same checkout — eight coins and a 30-minute rate lock.