We take cryptocurrency — so the coins you hold can buy real hardware.Pay in crypto, spend it on real hardware. Free insured shipping worldwide over $399. Plain, unbranded boxes, sent from Germany.Free insured shipping over $399. Your rate is locked for 30 minutes once checkout opens.Rate locked 30 minutes. Every item sealed, serial-checked and covered by a 24-month warranty.Sealed, 24-month warranty.

Saved items Sign in
Ten small clear clips with four short wires each

JacobsParts Inc.

JacobsParts Inc. LSA-Y5-10PK 10mm solderless 4-wire connector clip pigtail straight blade plug 10-pack

SKU CH-PYZB-916MA MPN LSA-Y5-10PK

Ten solderless clips connect 10 mm RGB LED strips without removing the silicone coating, each with a 15 cm pigtail

  • ColorRGB
  • Item Count10
  • Materialvinyl, Silicone
  • TypeLED Light Strip Connector
  • FeaturesWaterproof
  • Number of Wires4
  • Solder-free installation for waterproof RGB strips
  • Bottom-piercing design keeps silicone coating intact
  • 15 cm pigtail wires ready for power or extension
  • Ten connectors in one pack for multiple runs
  • Fits 10 mm 4-conductor 5050 RGB LED strip

JacobsParts 10-Pack Solderless LED Connectors

This 10-pack of ABI LSA-Y5-10PK clips provides a solder-free way to terminate waterproof 10mm RGB LED strips. Each connector punctures the silicone coating from underneath to contact the four-conductor PCB directly. The design preserves the strip's waterproof rating while leaving a 15 cm pigtail for wiring. Supplied as new items in a 10-piece pack.

Tool-Free Installation With Bottom-Piercing Contacts

Open the hinged lid, slide the strip in, and snap the lid shut to complete the connection. No soldering iron, flux, or coating removal is required. The main pitfall is misaligning the four conductors; if the strip sits crooked, one or more channels will not light. Press firmly until the lid clicks to ensure all pins penetrate the silicone cleanly.

Four-Conductor RGB Strips Up to 9 W Total

Each clip handles the four wires found on standard 5050 RGB tape. The 15 cm leads are long enough to reach a nearby controller or power supply inside the same enclosure. The pack supports a combined load of 9 watts across all ten connectors. Runs exceeding that power level or strips wider than 10 mm will need a different termination method.

Highlights

  • Solder-free installation for waterproof RGB strips
  • Bottom-piercing design keeps silicone coating intact
  • 15 cm pigtail wires ready for power or extension
  • Ten connectors in one pack for multiple runs
  • Fits 10 mm 4-conductor 5050 RGB LED strip

Specifications

BrandABI
ModelLSA-Y5-10PK
ColorRGB
Item Count10
Materialvinyl, Silicone
TypeLED Light Strip Connector
FeaturesWaterproof
Number of Wires4

Questions about this item

How can I verify the LSA-Y5-10PK connector is making proper contact after clamping it onto my waterproof strip?

After closing the connector top, gently tug the 15 cm pigtail wires to confirm they are held firmly. Power the RGB strip and check that all four channels — red, green, blue and common — light evenly without flicker.

What comes in the 10-pack and what must I supply separately to complete an installation?

The pack contains ten 10 mm 4-wire solderless connector clips with 15 cm vinyl and silicone pigtails. You must provide compatible waterproof 5050 RGB LED strip, a suitable power supply and any additional wiring or controllers.

Which version of the LSA-Y5 connector should I choose for my waterproof RGB LED strip?

Select the LSA-Y5-10PK when your strip is a waterproof 10 mm 4-conductor PCB type used with 5050 RGB LEDs. This 10-pack matches that exact profile and preserves the strip's waterproof coating.

Also in this aisle

People compared these

Same shelf, same checkout — eight coins and a 30-minute rate lock.